blob: 4845c0c09eb4dc742e63b4ac47cd28867c8ef0c0 (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
|
// MCU config
#define MICROPY_HW_BOARD_NAME "EK-RA4M1"
#define MICROPY_HW_MCU_NAME "RA4M1"
#define MICROPY_HW_MCU_SYSCLK 48000000
#define MICROPY_HW_MCU_PCLK 48000000
// module config
#define MICROPY_EMIT_THUMB (0)
#define MICROPY_EMIT_INLINE_THUMB (0)
#define MICROPY_PY_BUILTINS_COMPLEX (0)
#define MICROPY_PY_GENERATOR_PEND_THROW (0)
#define MICROPY_PY_MATH (0)
#define MICROPY_PY_HEAPQ (0)
#define MICROPY_PY_TIMEQ (0)
#define MICROPY_PY_THREAD (0)
// peripheral config
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_RTC_SOURCE (0) // 0: subclock, 1:LOCO
#define MICROPY_HW_ENABLE_ADC (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (1)
// board config
// UART
#define MICROPY_HW_UART0_TX (pin_P411) // REPL
#define MICROPY_HW_UART0_RX (pin_P410) // REPL
#define MICROPY_HW_UART1_TX (pin_P401) // PMOD B
#define MICROPY_HW_UART1_RX (pin_P402) // PMOD B
#define MICROPY_HW_UART1_CTS (pin_P403) // PMOD B
#define MICROPY_HW_UART2_TX (pin_P302)
#define MICROPY_HW_UART2_RX (pin_P301)
#define MICROPY_HW_UART2_CTS (pin_P203) // (Conflict with SPI1)
// #define MICROPY_HW_UART9_TX (pin_P602) // Disable (vector not registered)
// #define MICROPY_HW_UART9_RX (pin_P601) // Disable (vector not registered)
// #define MICROPY_HW_UART9_CTS (pin_P603) // Disable (vector not registered)
#define MICROPY_HW_UART_REPL HW_UART_0
#define MICROPY_HW_UART_REPL_BAUD 115200
// I2C (not supported)
// #define MICROPY_HW_I2C0_SCL (pin_P204) // Conflict with SPI1
// #define MICROPY_HW_I2C0_SDA (pin_P407) // Conflict with USB_VBUS
// #define MICROPY_HW_I2C0_SCL (pin_P400) // Conflict wiht PMOD B (GPIO)
// #define MICROPY_HW_I2C0_SDA (pin_P401) // Conflict with PMOD B (TXD1)
// #define MICROPY_HW_I2C1_SCL (pin_P100) // Conflict with PMOD A (MISOA_A)
// #define MICROPY_HW_I2C1_SDA (pin_P101) // Conflict with PMOD A (MOSIA_A)
// SPI
#define MICROPY_HW_SPI0_SSL (pin_P103) // PMOD A
#define MICROPY_HW_SPI0_RSPCK (pin_P102) // PMOD A
#define MICROPY_HW_SPI0_MISO (pin_P100) // PMOD A
#define MICROPY_HW_SPI0_MOSI (pin_P101) // PMOD A
#define MICROPY_HW_SPI1_SSL (pin_P206) // Use SSLB1 due to SSLB0 is used for TSCAP
// #define MICROPY_HW_SPI1_RSPCK (pin_P204) // Disable (vector not registered)
// #define MICROPY_HW_SPI1_MISO (pin_P202) // Disable (vector not registered)
// #define MICROPY_HW_SPI1_MOSI (pin_P203) // Disable (vector not registered)
// Switch
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_USRSW_PIN (pin_P105)
#define MICROPY_HW_USRSW_PULL (MP_HAL_PIN_PULL_NONE)
#define MICROPY_HW_USRSW_EXTI_MODE (MP_HAL_PIN_TRIGGER_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED1 (pin_P106)
#define MICROPY_HW_LED_ON(pin) mp_hal_pin_high(pin)
#define MICROPY_HW_LED_OFF(pin) mp_hal_pin_low(pin)
#define MICROPY_HW_LED_TOGGLE(pin) mp_hal_pin_toggle(pin)
|
