stmhal: L4: Add board definition files for STM32L476DISC.

6 files changed, 810 insertions, 0 deletions

diff --git a/stmhal/boards/STM32L476DISC/mpconfigboard.h b/stmhal/boards/STM32L476DISC/mpconfigboard.h
new file mode 100644
index 0000000000..f4617e67df
--- /dev/null
+++ b/stmhal/boards/STM32L476DISC/mpconfigboard.h
@@ -0,0 +1,63 @@
+#include STM32_HAL_H
+
+#define MICROPY_HW_BOARD_NAME       "L476-DISCO"
+#define MICROPY_HW_MCU_NAME         "STM32L476"
+
+#define MICROPY_HW_HAS_SWITCH       (1)
+#define MICROPY_HW_HAS_FLASH        (1)
+#define MICROPY_HW_HAS_SDCARD       (0)
+#define MICROPY_HW_HAS_MMA7660      (0)
+#define MICROPY_HW_HAS_LIS3DSH      (0)
+#define MICROPY_HW_HAS_LCD          (0)
+#define MICROPY_HW_ENABLE_RNG       (1)
+#define MICROPY_HW_ENABLE_RTC       (1)
+#define MICROPY_HW_ENABLE_TIMER     (1)
+#define MICROPY_HW_ENABLE_SERVO     (0)
+#define MICROPY_HW_ENABLE_DAC       (0)
+#define MICROPY_HW_ENABLE_CAN       (0)
+
+// HSE is 8MHz
+#define MICROPY_HW_CLK_PLLM (2)
+#define MICROPY_HW_CLK_PLLN (40)
+#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
+#define MICROPY_HW_CLK_PLLR (RCC_PLLP_DIV7)
+#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2)
+
+#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_4
+
+// USART config
+#define MICROPY_HW_UART2_PORT (GPIOD)
+#define MICROPY_HW_UART2_PINS (GPIO_PIN_5 | GPIO_PIN_6)
+
+// I2C busses
+#define MICROPY_HW_I2C1_SCL (pin_B6)
+#define MICROPY_HW_I2C1_SDA (pin_B7)
+// We use an array of baudrates and corresponding TIMINGR values.
+//
+// The value 0x90112626 was obtained from the DISCOVERY_I2C1_TIMING constant
+// defined in the STM32L4Cube file Drivers/BSP/STM32L476G-Discovery/stm32l476g_discovery.h
+#define MICROPY_HW_I2C_BAUDRATE_TIMING  {{100000, 0x90112626}}
+#define MICROPY_HW_I2C_BAUDRATE_DEFAULT 100000
+#define MICROPY_HW_I2C_BAUDRATE_MAX     100000
+
+// SPI busses
+#define MICROPY_HW_SPI2_NSS     (pin_D0)
+#define MICROPY_HW_SPI2_SCK     (pin_D1)
+#define MICROPY_HW_SPI2_MISO    (pin_D3)
+#define MICROPY_HW_SPI2_MOSI    (pin_D4)
+
+// Joystick is pulled low. Pressing the button makes the input go high.
+#define MICROPY_HW_USRSW_PIN        (pin_A0)
+#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
+#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
+#define MICROPY_HW_USRSW_PRESSED    (1)
+
+// LEDs
+#define MICROPY_HW_LED1             (pin_B2) // red
+#define MICROPY_HW_LED2             (pin_E8) // green
+#define MICROPY_HW_LED_OTYPE        (GPIO_MODE_OUTPUT_PP)
+#define MICROPY_HW_LED_ON(pin)      (pin->gpio->BSRR = pin->pin_mask)
+#define MICROPY_HW_LED_OFF(pin)     (pin->gpio->BSRR = pin->pin_mask<<16)
+
+// USB config
+// #define MICROPY_HW_USB_OTG_ID_PIN      (pin_C12) // This is not the official ID Pin which should be PA10
diff --git a/stmhal/boards/STM32L476DISC/mpconfigboard.mk b/stmhal/boards/STM32L476DISC/mpconfigboard.mk
new file mode 100644
index 0000000000..7049d7206f
--- /dev/null
+++ b/stmhal/boards/STM32L476DISC/mpconfigboard.mk
@@ -0,0 +1,4 @@
+MCU_SERIES = l4
+CMSIS_MCU = STM32L476xx
+AF_FILE = boards/stm32l476_af.csv
+LD_FILE = boards/stm32l476xg.ld
diff --git a/stmhal/boards/STM32L476DISC/pins.csv b/stmhal/boards/STM32L476DISC/pins.csv
new file mode 100644
index 0000000000..52f96b669c
--- /dev/null
+++ b/stmhal/boards/STM32L476DISC/pins.csv
@@ -0,0 +1,114 @@
+PA0,PA0
+PA1,PA1
+PA2,PA2
+PA3,PA3
+PA4,PA4
+PA5,PA5
+PA6,PA6
+PA7,PA7
+PA8,PA8
+PA9,PA9
+PA10,PA10
+PA11,PA11
+PA12,PA12
+PA13,PA13
+PA14,PA14
+PA15,PA15
+PB0,PB0
+PB1,PB1
+PB2,PB2
+PB3,PB3
+PB4,PB4
+PB5,PB5
+PB6,PB6
+PB7,PB7
+PB8,PB8
+PB9,PB9
+PB10,PB10
+PB11,PB11
+PB12,PB12
+PB13,PB13
+PB14,PB14
+PB15,PB15
+PC0,PC0
+PC1,PC1
+PC2,PC2
+PC3,PC3
+PC4,PC4
+PC5,PC5
+PC6,PC6
+PC7,PC7
+PC8,PC8
+PC9,PC9
+PC10,PC10
+PC11,PC11
+PC12,PC12
+PC13,PC13
+PC14,PC14
+PC15,PC15
+PD0,PD0
+PD1,PD1
+PD2,PD2
+PD3,PD3
+PD4,PD4
+PD5,PD5
+PD6,PD6
+PD7,PD7
+PD8,PD8
+PD9,PD9
+PD10,PD10
+PD11,PD11
+PD12,PD12
+PD13,PD13
+PD14,PD14
+PD15,PD15
+PE0,PE0
+PE1,PE1
+PE2,PE2
+PE3,PE3
+PE4,PE4
+PE5,PE5
+PE6,PE6
+PE7,PE7
+PE8,PE8
+PE9,PE9
+PE10,PE10
+PE11,PE11
+PE12,PE12
+PE13,PE13
+PE14,PE14
+PE15,PE15
+PF0,PF0
+PF1,PF1
+PF2,PF2
+PF3,PF3
+PF4,PF4
+PF5,PF5
+PF6,PF6
+PF7,PF7
+PF8,PF8
+PF9,PF9
+PF10,PF10
+PF11,PF11
+PF12,PF12
+PF13,PF13
+PF14,PF14
+PF15,PF15
+PG0,PG0
+PG1,PG1
+PG2,PG2
+PG3,PG3
+PG4,PG4
+PG5,PG5
+PG6,PG6
+PG7,PG7
+PG8,PG8
+PG9,PG9
+PG10,PG10
+PG11,PG11
+PG12,PG12
+PG13,PG13
+PG14,PG14
+PG15,PG15
+PH0,PH0
+PH1,PH1
diff --git a/stmhal/boards/STM32L476DISC/stm32l4xx_hal_conf.h b/stmhal/boards/STM32L476DISC/stm32l4xx_hal_conf.h
new file mode 100644
index 0000000000..9348e06790
--- /dev/null
+++ b/stmhal/boards/STM32L476DISC/stm32l4xx_hal_conf.h
@@ -0,0 +1,373 @@
+/**
+  ******************************************************************************
+  * @file    stm32l4xx_hal_conf.h
+  * @author  MCD Application Team
+  * @version V1.2.0
+  * @date    25-November-2015
+  * @brief   HAL configuration template file.
+  *          This file should be copied to the application folder and renamed
+  *          to stm32l4xx_hal_conf.h.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L4xx_HAL_CONF_H
+#define __STM32L4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define USE_USB_FS
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CAN_MODULE_ENABLED
+/* #define HAL_COMP_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+#define HAL_DAC_MODULE_ENABLED
+/* #define HAL_DFSDM_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_FIREWALL_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_HCD_MODULE_ENABLED */
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LCD_MODULE_ENABLED */
+/* #define HAL_LPTIM_MODULE_ENABLED */
+/* #define HAL_OPAMP_MODULE_ENABLED */
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+/* #define HAL_QSPI_MODULE_ENABLED */
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RNG_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+/* #define HAL_SAI_MODULE_ENABLED */
+#define HAL_SD_MODULE_ENABLED
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_SMBUS_MODULE_ENABLED */
+#define HAL_SPI_MODULE_ENABLED
+/* #define HAL_SWPMI_MODULE_ENABLED */
+#define HAL_TIM_MODULE_ENABLED
+/* #define HAL_TSC_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).  
+  */
+#if !defined  (HSE_VALUE) 
+  #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT    ((uint32_t)100)   /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal Multiple Speed oscillator (MSI) default value.
+  *        This value is the default MSI range value after Reset.
+  */
+#if !defined  (MSI_VALUE)
+  #define MSI_VALUE    ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* MSI_VALUE */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL). 
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE    ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE) 
+ #define LSI_VALUE  ((uint32_t)32000)       /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
+                                             The real value may vary depending on the variations
+                                             in voltage and temperature.  */
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  *        This value is used by the UART, RTC HAL module to compute the system frequency
+  */
+#if !defined  (LSE_VALUE)
+  #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
+#endif /* LSE_VALUE */
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief External clock source for SAI1 peripheral
+  *        This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source 
+  *        frequency.
+  */
+#if !defined  (EXTERNAL_SAI1_CLOCK_VALUE)
+  #define EXTERNAL_SAI1_CLOCK_VALUE    ((uint32_t)48000) /*!< Value of the SAI1 External clock source in Hz*/
+#endif /* EXTERNAL_SAI1_CLOCK_VALUE */
+
+/**
+  * @brief External clock source for SAI2 peripheral
+  *        This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source 
+  *        frequency.
+  */
+#if !defined  (EXTERNAL_SAI2_CLOCK_VALUE)
+  #define EXTERNAL_SAI2_CLOCK_VALUE    ((uint32_t)48000) /*!< Value of the SAI2 External clock source in Hz*/
+#endif /* EXTERNAL_SAI2_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+#define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            ((uint32_t)0x00) /*!< tick interrupt priority */
+#define  USE_RTOS                     0
+#define  PREFETCH_ENABLE              1
+#define  INSTRUCTION_CACHE_ENABLE     1
+#define  DATA_CACHE_ENABLE            1
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1 */
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+  #include "stm32l4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+  #include "stm32l4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+  #include "stm32l4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+  #include "stm32l4xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+  #include "stm32l4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+  #include "stm32l4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+  #include "stm32l4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_COMP_MODULE_ENABLED
+  #include "stm32l4xx_hal_comp.h"
+#endif /* HAL_COMP_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+  #include "stm32l4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+  #include "stm32l4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+  #include "stm32l4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FIREWALL_MODULE_ENABLED
+  #include "stm32l4xx_hal_firewall.h"
+#endif /* HAL_FIREWALL_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+  #include "stm32l4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+  #include "stm32l4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+  #include "stm32l4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+  #include "stm32l4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32l4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32l4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LCD_MODULE_ENABLED
+ #include "stm32l4xx_hal_lcd.h"
+#endif /* HAL_LCD_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+#include "stm32l4xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_OPAMP_MODULE_ENABLED
+#include "stm32l4xx_hal_opamp.h"
+#endif /* HAL_OPAMP_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32l4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32l4xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32l4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32l4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32l4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32l4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32l4xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32l4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_SWPMI_MODULE_ENABLED
+ #include "stm32l4xx_hal_swpmi.h"
+#endif /* HAL_SWPMI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32l4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_TSC_MODULE_ENABLED
+ #include "stm32l4xx_hal_tsc.h"
+#endif /* HAL_TSC_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32l4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32l4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32l4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32l4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32l4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32l4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32l4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr: If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+  #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+  void assert_failed(uint8_t* file, uint32_t line);
+#else
+  #define assert_param(expr) ((void)0)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/stmhal/boards/stm32l476_af.csv b/stmhal/boards/stm32l476_af.csv
new file mode 100644
index 0000000000..6dea7e092e
--- /dev/null
+++ b/stmhal/boards/stm32l476_af.csv
@@ -0,0 +1,122 @@
+Port,,AF0,AF1,AF2,AF3,AF4,AF5,AF6,AF7,AF8,AF9,AF10,AF11,AF12,AF13,AF14,AF15
+,,SYS_AF,TIM1/TIM2/TIM5/TIM8/LPTIM1,TIM1/TIM2/TIM3/TIM4/TIM5,TIM8,I2C1/I2C2/I2C3,SPI1/SPI2,SPI3/DFSDM,USART1/USART2/USART3,"UART4, 
+UART5, 
+LPUART1","CAN1, TSC","OTG_FS, QUADSPI",LCD,"SDMMC1, COMP1, 
+COMP2, FMC, 
+SWPMI1","SAI1, SAI2","TIM2, TIM15, 
+TIM16, TIM17, 
+LPTIM2",EVENTOUT
+PortA,PA0,,TIM2_CH1,TIM5_CH1,TIM8_ETR,,,,USART2_CTS,UART4_TX,,,,,SAI1_EXTCLK,TIM2_ETR,EVENTOUT
+PortA,PA1,,TIM2_CH2,TIM5_CH2,,,,,USART2_RTS_DE,UART4_RX,,,LCD_SEG0,,,TIM15_CH1N,EVENTOUT
+PortA,PA2,,TIM2_CH3,TIM5_CH3,,,,,USART2_TX,,,,LCD_SEG1,,SAI2_EXTCLK,TIM15_CH1,EVENTOUT
+PortA,PA3,,TIM2_CH4,TIM5_CH4,,,,,USART2_RX,,,,LCD_SEG2,,,TIM15_CH2,EVENTOUT
+PortA,PA4,,,,,,SPI1_NSS,SPI3_NSS,USART2_CK,,,,,,SAI1_FS_B,LPTIM2_OUT,EVENTOUT
+PortA,PA5,,TIM2_CH1,TIM2_ETR,TIM8_CH1N,,SPI1_SCK,,,,,,,,,LPTIM2_ETR,EVENTOUT
+PortA,PA6,,TIM1_BKIN,TIM3_CH1,TIM8_BKIN,,SPI1_MISO,,USART3_CTS,,,QUADSPI_BK1_IO3,LCD_SEG3,TIM1_BKIN_COMP2,TIM8_BKIN_COMP2,TIM16_CH1,EVENTOUT
+PortA,PA7,,TIM1_CH1N,TIM3_CH2,TIM8_CH1N,,SPI1_MOSI,,,,,QUADSPI_BK1_IO2,LCD_SEG4,,,TIM17_CH1,EVENTOUT
+PortA,PA8,MCO,TIM1_CH1,,,,,,USART1_CK,,,OTG_FS_SOF,LCD_COM0,,,LPTIM2_OUT,EVENTOUT
+PortA,PA9,,TIM1_CH2,,,,,,USART1_TX,,,,LCD_COM1,,,TIM15_BKIN,EVENTOUT
+PortA,PA10,,TIM1_CH3,,,,,,USART1_RX,,,OTG_FS_ID,LCD_COM2,,,TIM17_BKIN,EVENTOUT
+PortA,PA11,,TIM1_CH4,TIM1_BKIN2,,,,,USART1_CTS,,CAN1_RX,OTG_FS_DM,,TIM1_BKIN2_COMP1,,,EVENTOUT
+PortA,PA12,,TIM1_ETR,,,,,,USART1_RTS_DE,,CAN1_TX,OTG_FS_DP,,,,,EVENTOUT
+PortA,PA13,JTMS-SWDIO,IR_OUT,,,,,,,,,OTG_FS_NOE,,,,,EVENTOUT
+PortA,PA14,JTCK-SWCLK,,,,,,,,,,,,,,,EVENTOUT
+PortA,PA15,JTDI,TIM2_CH1,TIM2_ETR,,,SPI1_NSS,SPI3_NSS,,UART4_RTS_DE,TSC_G3_IO1,,LCD_SEG17,,SAI2_FS_B,,EVENTOUT
+PortB,PB0,,TIM1_CH2N,TIM3_CH3,TIM8_CH2N,,,,USART3_CK,,,QUADSPI_BK1_IO1,LCD_SEG5,COMP1_OUT,,,EVENTOUT
+PortB,PB1,,TIM1_CH3N,TIM3_CH4,TIM8_CH3N,,,DFSDM_DATIN0,USART3_RTS_DE,,,QUADSPI_BK1_IO0,LCD_SEG6,,,LPTIM2_IN1,EVENTOUT
+PortB,PB2,RTC_OUT,LPTIM1_OUT,,,I2C3_SMBA,,DFSDM_CKIN0,,,,,,,,,EVENTOUT
+PortB,PB3,JTDO-TRACESWO,TIM2_CH2,,,,SPI1_SCK,SPI3_SCK,USART1_RTS_DE,,,,LCD_SEG7,,SAI1_SCK_B,,EVENTOUT
+PortB,PB4,NJTRST,,TIM3_CH1,,,SPI1_MISO,SPI3_MISO,USART1_CTS,UART5_RTS_DE,TSC_G2_IO1,,LCD_SEG8,,SAI1_MCLK_B,TIM17_BKIN,EVENTOUT
+PortB,PB5,,LPTIM1_IN1,TIM3_CH2,,I2C1_SMBA,SPI1_MOSI,SPI3_MOSI,USART1_CK,UART5_CTS,TSC_G2_IO2,,LCD_SEG9,COMP2_OUT,SAI1_SD_B,TIM16_BKIN,EVENTOUT
+PortB,PB6,,LPTIM1_ETR,TIM4_CH1,TIM8_BKIN2,I2C1_SCL,,DFSDM_DATIN5,USART1_TX,,TSC_G2_IO3,,,TIM8_BKIN2_COMP2,SAI1_FS_B,TIM16_CH1N,EVENTOUT
+PortB,PB7,,LPTIM1_IN2,TIM4_CH2,TIM8_BKIN,I2C1_SDA,,DFSDM_CKIN5,USART1_RX,UART4_CTS,TSC_G2_IO4,,LCD_SEG21,FMC_NL,TIM8_BKIN_COMP1,TIM17_CH1N,EVENTOUT
+PortB,PB8,,,TIM4_CH3,,I2C1_SCL,,DFSDM_DATIN6,,,CAN1_RX,,LCD_SEG16,SDMMC1_D4,SAI1_MCLK_A,TIM16_CH1,EVENTOUT
+PortB,PB9,,IR_OUT,TIM4_CH4,,I2C1_SDA,SPI2_NSS,DFSDM_CKIN6,,,CAN1_TX,,LCD_COM3,SDMMC1_D5,SAI1_FS_A,TIM17_CH1,EVENTOUT
+PortB,PB10,,TIM2_CH3,,,I2C2_SCL,SPI2_SCK,DFSDM_DATIN7,USART3_TX,LPUART1_RX,,QUADSPI_CLK,LCD_SEG10,COMP1_OUT,SAI1_SCK_A,,EVENTOUT
+PortB,PB11,,TIM2_CH4,,,I2C2_SDA,,DFSDM_CKIN7,USART3_RX,LPUART1_TX,,QUADSPI_NCS,LCD_SEG11,COMP2_OUT,,,EVENTOUT
+PortB,PB12,,TIM1_BKIN,,TIM1_BKIN_COMP2,I2C2_SMBA,SPI2_NSS,DFSDM_DATIN1,USART3_CK,LPUART1_RTS_DE,TSC_G1_IO1,,LCD_SEG12,SWPMI1_IO,SAI2_FS_A,TIM15_BKIN,EVENTOUT
+PortB,PB13,,TIM1_CH1N,,,I2C2_SCL,SPI2_SCK,DFSDM_CKIN1,USART3_CTS,LPUART1_CTS,TSC_G1_IO2,,LCD_SEG13,SWPMI1_TX,SAI2_SCK_A,TIM15_CH1N,EVENTOUT
+PortB,PB14,,TIM1_CH2N,,TIM8_CH2N,I2C2_SDA,SPI2_MISO,DFSDM_DATIN2,USART3_RTS_DE,,TSC_G1_IO3,,LCD_SEG14,SWPMI1_RX,SAI2_MCLK_A,TIM15_CH1,EVENTOUT
+PortB,PB15,RTC_REFIN,TIM1_CH3N,,TIM8_CH3N,,SPI2_MOSI,DFSDM_CKIN2,,,TSC_G1_IO4,,LCD_SEG15,SWPMI1_SUSPEND,SAI2_SD_A,TIM15_CH2,EVENTOUT
+PortC,PC0,,LPTIM1_IN1,,,I2C3_SCL,,DFSDM_DATIN4,,LPUART1_RX,,,LCD_SEG18,,,LPTIM2_IN1,EVENTOUT
+PortC,PC1,,LPTIM1_OUT,,,I2C3_SDA,,DFSDM_CKIN4,,LPUART1_TX,,,LCD_SEG19,,,,EVENTOUT
+PortC,PC2,,LPTIM1_IN2,,,,SPI2_MISO,DFSDM_CKOUT,,,,,LCD_SEG20,,,,EVENTOUT
+PortC,PC3,,LPTIM1_ETR,,,,SPI2_MOSI,,,,,,LCD_VLCD,,SAI1_SD_A,LPTIM2_ETR,EVENTOUT
+PortC,PC4,,,,,,,,USART3_TX,,,,LCD_SEG22,,,,EVENTOUT
+PortC,PC5,,,,,,,,USART3_RX,,,,LCD_SEG23,,,,EVENTOUT
+PortC,PC6,,,TIM3_CH1,TIM8_CH1,,,DFSDM_CKIN3,,,TSC_G4_IO1,,LCD_SEG24,SDMMC1_D6,SAI2_MCLK_A,,EVENTOUT
+PortC,PC7,,,TIM3_CH2,TIM8_CH2,,,DFSDM_DATIN3,,,TSC_G4_IO2,,LCD_SEG25,SDMMC1_D7,SAI2_MCLK_B,,EVENTOUT
+PortC,PC8,,,TIM3_CH3,TIM8_CH3,,,,,,TSC_G4_IO3,,LCD_SEG26,SDMMC1_D0,,,EVENTOUT
+PortC,PC9,,TIM8_BKIN2,TIM3_CH4,TIM8_CH4,,,,,,TSC_G4_IO4,OTG_FS_NOE,LCD_SEG27,SDMMC1_D1,SAI2_EXTCLK,TIM8_BKIN2_COMP1,EVENTOUT
+PortC,PC10,,,,,,,SPI3_SCK,USART3_TX,UART4_TX,TSC_G3_IO2,,LCD_COM4/LCD_SEG28/LCD_SEG40,SDMMC1_D2,SAI2_SCK_B,,EVENTOUT
+PortC,PC11,,,,,,,SPI3_MISO,USART3_RX,UART4_RX,TSC_G3_IO3,,LCD_COM5/LCD_SEG29/LCD_SEG41,SDMMC1_D3,SAI2_MCLK_B,,EVENTOUT
+PortC,PC12,,,,,,,SPI3_MOSI,USART3_CK,UART5_TX,TSC_G3_IO4,,LCD_COM6/LCD_SEG30/LCD_SEG42,SDMMC1_CK,SAI2_SD_B,,EVENTOUT
+PortC,PC13,,,,,,,,,,,,,,,,EVENTOUT
+PortC,PC14,,,,,,,,,,,,,,,,EVENTOUT
+PortC,PC15,,,,,,,,,,,,,,,,EVENTOUT
+PortD,PD0,,,,,,SPI2_NSS,DFSDM_DATIN7,,,CAN1_RX,,,FMC_D2,,,EVENTOUT
+PortD,PD1,,,,,,SPI2_SCK,DFSDM_CKIN7,,,CAN1_TX,,,FMC_D3,,,EVENTOUT
+PortD,PD2,,,TIM3_ETR,,,,,USART3_RTS_DE,UART5_RX,TSC_SYNC,,LCD_COM7/LCD_SEG31/LCD_SEG43,SDMMC1_CMD,,,EVENTOUT
+PortD,PD3,,,,,,SPI2_MISO,DFSDM_DATIN0,USART2_CTS,,,,,FMC_CLK,,,EVENTOUT
+PortD,PD4,,,,,,SPI2_MOSI,DFSDM_CKIN0,USART2_RTS_DE,,,,,FMC_NOE,,,EVENTOUT
+PortD,PD5,,,,,,,,USART2_TX,,,,,FMC_NWE,,,EVENTOUT
+PortD,PD6,,,,,,,DFSDM_DATIN1,USART2_RX,,,,,FMC_NWAIT,SAI1_SD_A,,EVENTOUT
+PortD,PD7,,,,,,,DFSDM_CKIN1,USART2_CK,,,,,FMC_NE1,,,EVENTOUT
+PortD,PD8,,,,,,,,USART3_TX,,,,LCD_SEG28,FMC_D13,,,EVENTOUT
+PortD,PD9,,,,,,,,USART3_RX,,,,LCD_SEG29,FMC_D14,SAI2_MCLK_A,,EVENTOUT
+PortD,PD10,,,,,,,,USART3_CK,,TSC_G6_IO1,,LCD_SEG30,FMC_D15,SAI2_SCK_A,,EVENTOUT
+PortD,PD11,,,,,,,,USART3_CTS,,TSC_G6_IO2,,LCD_SEG31,FMC_A16,SAI2_SD_A,LPTIM2_ETR,EVENTOUT
+PortD,PD12,,,TIM4_CH1,,,,,USART3_RTS_DE,,TSC_G6_IO3,,LCD_SEG32,FMC_A17,SAI2_FS_A,LPTIM2_IN1,EVENTOUT
+PortD,PD13,,,TIM4_CH2,,,,,,,TSC_G6_IO4,,LCD_SEG33,FMC_A18,,LPTIM2_OUT,EVENTOUT
+PortD,PD14,,,TIM4_CH3,,,,,,,,,LCD_SEG34,FMC_D0,,,EVENTOUT
+PortD,PD15,,,TIM4_CH4,,,,,,,,,LCD_SEG35,FMC_D1,,,EVENTOUT
+PortE,PE0,,,TIM4_ETR,,,,,,,,,LCD_SEG36,FMC_NBL0,,TIM16_CH1,EVENTOUT
+PortE,PE1,,,,,,,,,,,,LCD_SEG37,FMC_NBL1,,TIM17_CH1,EVENTOUT
+PortE,PE2,TRACECK,,TIM3_ETR,,,,,,,TSC_G7_IO1,,LCD_SEG38,FMC_A23,SAI1_MCLK_A,,EVENTOUT
+PortE,PE3,TRACED0,,TIM3_CH1,,,,,,,TSC_G7_IO2,,LCD_SEG39,FMC_A19,SAI1_SD_B,,EVENTOUT
+PortE,PE4,TRACED1,,TIM3_CH2,,,,DFSDM_DATIN3,,,TSC_G7_IO3,,,FMC_A20,SAI1_FS_A,,EVENTOUT
+PortE,PE5,TRACED2,,TIM3_CH3,,,,DFSDM_CKIN3,,,TSC_G7_IO4,,,FMC_A21,SAI1_SCK_A,,EVENTOUT
+PortE,PE6,TRACED3,,TIM3_CH4,,,,,,,,,,FMC_A22,SAI1_SD_A,,EVENTOUT
+PortE,PE7,,TIM1_ETR,,,,,DFSDM_DATIN2,,,,,,FMC_D4,SAI1_SD_B,,EVENTOUT
+PortE,PE8,,TIM1_CH1N,,,,,DFSDM_CKIN2,,,,,,FMC_D5,SAI1_SCK_B,,EVENTOUT
+PortE,PE9,,TIM1_CH1,,,,,DFSDM_CKOUT,,,,,,FMC_D6,SAI1_FS_B,,EVENTOUT
+PortE,PE10,,TIM1_CH2N,,,,,DFSDM_DATIN4,,,TSC_G5_IO1,QUADSPI_CLK,,FMC_D7,SAI1_MCLK_B,,EVENTOUT
+PortE,PE11,,TIM1_CH2,,,,,DFSDM_CKIN4,,,TSC_G5_IO2,QUADSPI_NCS,,FMC_D8,,,EVENTOUT
+PortE,PE12,,TIM1_CH3N,,,,SPI1_NSS,DFSDM_DATIN5,,,TSC_G5_IO3,QUADSPI_BK1_IO0,,FMC_D9,,,EVENTOUT
+PortE,PE13,,TIM1_CH3,,,,SPI1_SCK,DFSDM_CKIN5,,,TSC_G5_IO4,QUADSPI_BK1_IO1,,FMC_D10,,,EVENTOUT
+PortE,PE14,,TIM1_CH4,TIM1_BKIN2,TIM1_BKIN2_COMP2,,SPI1_MISO,,,,,QUADSPI_BK1_IO2,,FMC_D11,,,EVENTOUT
+PortE,PE15,,TIM1_BKIN,,TIM1_BKIN_COMP1,,SPI1_MOSI,,,,,QUADSPI_BK1_IO3,,FMC_D12,,,EVENTOUT
+PortF,PF0,,,,,I2C2_SDA,,,,,,,,FMC_A0,,,EVENTOUT
+PortF,PF1,,,,,I2C2_SCL,,,,,,,,FMC_A1,,,EVENTOUT
+PortF,PF2,,,,,I2C2_SMBA,,,,,,,,FMC_A2,,,EVENTOUT
+PortF,PF3,,,,,,,,,,,,,FMC_A3,,,EVENTOUT
+PortF,PF4,,,,,,,,,,,,,FMC_A4,,,EVENTOUT
+PortF,PF5,,,,,,,,,,,,,FMC_A5,,,EVENTOUT
+PortF,PF6,,TIM5_ETR,TIM5_CH1,,,,,,,,,,,SAI1_SD_B,,EVENTOUT
+PortF,PF7,,,TIM5_CH2,,,,,,,,,,,SAI1_MCLK_B,,EVENTOUT
+PortF,PF8,,,TIM5_CH3,,,,,,,,,,,SAI1_SCK_B,,EVENTOUT
+PortF,PF9,,,TIM5_CH4,,,,,,,,,,,SAI1_FS_B,TIM15_CH1,EVENTOUT
+PortF,PF10,,,,,,,,,,,,,,,TIM15_CH2,EVENTOUT
+PortF,PF11,,,,,,,,,,,,,,,,EVENTOUT
+PortF,PF12,,,,,,,,,,,,,FMC_A6,,,EVENTOUT
+PortF,PF13,,,,,,,DFSDM_DATIN6,,,,,,FMC_A7,,,EVENTOUT
+PortF,PF14,,,,,,,DFSDM_CKIN6,,,TSC_G8_IO1,,,FMC_A8,,,EVENTOUT
+PortF,PF15,,,,,,,,,,TSC_G8_IO2,,,FMC_A9,,,EVENTOUT
+PortG,PG0,,,,,,,,,,TSC_G8_IO3,,,FMC_A10,,,EVENTOUT
+PortG,PG1,,,,,,,,,,TSC_G8_IO4,,,FMC_A11,,,EVENTOUT
+PortG,PG2,,,,,,SPI1_SCK,,,,,,,FMC_A12,SAI2_SCK_B,,EVENTOUT
+PortG,PG3,,,,,,SPI1_MISO,,,,,,,FMC_A13,SAI2_FS_B,,EVENTOUT
+PortG,PG4,,,,,,SPI1_MOSI,,,,,,,FMC_A14,SAI2_MCLK_B,,EVENTOUT
+PortG,PG5,,,,,,SPI1_NSS,,,LPUART1_CTS,,,,FMC_A15,SAI2_SD_B,,EVENTOUT
+PortG,PG6,,,,,I2C3_SMBA,,,,LPUART1_RTS_DE,,,,,,,EVENTOUT
+PortG,PG7,,,,,I2C3_SCL,,,,LPUART1_TX,,,,FMC_INT3,,,EVENTOUT
+PortG,PG8,,,,,I2C3_SDA,,,,LPUART1_RX,,,,,,,EVENTOUT
+PortG,PG9,,,,,,,SPI3_SCK,USART1_TX,,,,,FMC_NCE3/FMC_NE2,SAI2_SCK_A,TIM15_CH1N,EVENTOUT
+PortG,PG10,,LPTIM1_IN1,,,,,SPI3_MISO,USART1_RX,,,,,FMC_NE3,SAI2_FS_A,TIM15_CH1,EVENTOUT
+PortG,PG11,,LPTIM1_IN2,,,,,SPI3_MOSI,USART1_CTS,,,,,,SAI2_MCLK_A,TIM15_CH2,EVENTOUT
+PortG,PG12,,LPTIM1_ETR,,,,,SPI3_NSS,USART1_RTS_DE,,,,,FMC_NE4,SAI2_SD_A,,EVENTOUT
+PortG,PG13,,,,,I2C1_SDA,,,USART1_CK,,,,,FMC_A24,,,EVENTOUT
+PortG,PG14,,,,,I2C1_SCL,,,,,,,,FMC_A25,,,EVENTOUT
+PortG,PG15,,LPTIM1_OUT,,,I2C1_SMBA,,,,,,,,,,,EVENTOUT
+PortH,PH0,,,,,,,,,,,,,,,,EVENTOUT
+PortH,PH1,,,,,,,,,,,,,,,,EVENTOUT
diff --git a/stmhal/boards/stm32l476xg.ld b/stmhal/boards/stm32l476xg.ld
new file mode 100644
index 0000000000..1f2b6694ca
--- /dev/null
+++ b/stmhal/boards/stm32l476xg.ld
@@ -0,0 +1,134 @@
+/*
+    GNU linker script for STM32L476XG
+*/
+
+/* Specify the memory areas */
+MEMORY
+{                                                   
+    FLASH (rx)      : ORIGIN = 0x08000000, LENGTH = 1024K
+    FLASH_ISR (rx)  : ORIGIN = 0x08000000, LENGTH = 0x0000800 /* sector 0, 2 KiB */
+    FLASH_FS (r)    : ORIGIN = 0x08000800, LENGTH = 0x001F800 /* sectors 1-63 (2K each = 126 KiB) */
+    FLASH_TEXT (rx) : ORIGIN = 0x08020000, LENGTH = 0x0080000 /* Sector starting @ 64 */
+    RAM (xrw)       : ORIGIN = 0x20000000, LENGTH = 96K
+    SRAM2 (xrw)     : ORIGIN = 0x10000000, LENGTH = 32K
+}
+
+ENTRY(Reset_Handler)
+
+/* produce a link error if there is not this amount of RAM for these sections */
+_minimum_stack_size = 2K;
+_minimum_heap_size = 16K;
+ 
+/* Define the top end of the stack.  The stack is full descending so begins just
+   above last byte of RAM.  Note that EABI requires the stack to be 8-byte
+   aligned for a call. */
+_estack = ORIGIN(RAM) + LENGTH(RAM);
+
+/* RAM extents for the garbage collector */
+_ram_end = ORIGIN(RAM) + LENGTH(RAM);
+_heap_end = 0x20014000; /* tunable */
+
+
+/* define output sections */
+SECTIONS
+{
+    /* The startup code goes first into FLASH */
+    .isr_vector :
+    {
+        . = ALIGN(4);
+        KEEP(*(.isr_vector)) /* Startup code */
+
+        . = ALIGN(4);
+    } >FLASH_ISR
+   
+    /* The program code and other data goes into FLASH */
+    .text :
+    {
+        . = ALIGN(4);
+        *(.text)           /* .text sections (code) */
+        *(.text*)          /* .text* sections (code) */
+        *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+        *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    /*  *(.glue_7)   */    /* glue arm to thumb code */
+    /*  *(.glue_7t)  */    /* glue thumb to arm code */
+
+        . = ALIGN(4);
+        _etext = .;        /* define a global symbol at end of code */
+    } >FLASH_TEXT
+     
+    /*
+    .ARM.extab :
+    {
+        *(.ARM.extab* .gnu.linkonce.armextab.*)
+    } >FLASH
+
+    .ARM :
+    {
+        __exidx_start = .;
+        *(.ARM.exidx*)
+        __exidx_end = .;
+    } >FLASH
+    */
+        
+    /* used by the startup to initialize data */
+    _sidata = LOADADDR(.data);
+        
+    /* This is the initialized data section
+    The program executes knowing that the data is in the RAM
+    but the loader puts the initial values in the FLASH (inidata).
+    It is one task of the startup to copy the initial values from FLASH to RAM. */
+    .data :
+    {
+        . = ALIGN(4);
+        _sdata = .;        /* create a global symbol at data start; used by startup code in order to initialise the .data section in RAM */
+        _ram_start = .;    /* create a global symbol at ram start for garbage collector */
+        *(.data)           /* .data sections */
+        *(.data*)          /* .data* sections */
+
+        . = ALIGN(4);
+        _edata = .;        /* define a global symbol at data end; used by startup code in order to initialise the .data section in RAM */
+    } >RAM AT> FLASH_TEXT
+            
+    /* Uninitialized data section */
+    .bss :
+    {
+        . = ALIGN(4);
+        _sbss = .;         /* define a global symbol at bss start; used by startup code */
+        *(.bss)
+        *(.bss*)
+        *(COMMON)
+
+        . = ALIGN(4);
+        _ebss = .;         /* define a global symbol at bss end; used by startup code and GC */
+    } >RAM
+
+    /* this is to define the start of the heap, and make sure we have a minimum size */
+    .heap :
+    {
+        . = ALIGN(4);
+        PROVIDE ( end = . );
+        PROVIDE ( _end = . );
+        _heap_start = .;    /* define a global symbol at heap start */
+        . = . + _minimum_heap_size;
+    } >RAM
+
+    /* this just checks there is enough RAM for the stack */
+    .stack :
+    {
+        . = ALIGN(4);
+        . = . + _minimum_stack_size;
+        . = ALIGN(4);
+    } >RAM
+
+    /* Remove information from the standard libraries */
+    /*
+    /DISCARD/ :
+    {
+        libc.a ( * )
+        libm.a ( * )
+        libgcc.a ( * )
+    }
+    */
+
+    .ARM.attributes 0 : { *(.ARM.attributes) }
+}