blob: 037302c6bab660a50d97539cf6fb0d71a40c609a (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
|
#define MICROPY_HW_BOARD_NAME "PYBLITEv1.0"
#define MICROPY_HW_MCU_NAME "STM32F411RE"
#define MICROPY_PY_SYS_PLATFORM "pyboard"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_SDCARD (1)
#define MICROPY_HW_HAS_MMA7660 (1)
#define MICROPY_HW_HAS_LIS3DSH (0)
#define MICROPY_HW_HAS_LCD (1)
#define MICROPY_HW_ENABLE_RNG (0)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (1)
#define MICROPY_HW_ENABLE_DAC (0)
#define MICROPY_HW_ENABLE_CAN (0)
// HSE is 12MHz
#define MICROPY_HW_CLK_PLLM (12)
#define MICROPY_HW_CLK_PLLN (192)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (4)
#define MICROPY_HW_CLK_LAST_FREQ (1)
// Pyboard lite has an optional 32kHz crystal
#define MICROPY_HW_RTC_USE_LSE (1)
#define MICROPY_HW_RTC_USE_US (0)
#define MICROPY_HW_RTC_USE_CALOUT (1)
// UART config
#define MICROPY_HW_UART1_NAME "XB"
#define MICROPY_HW_UART1_PORT (GPIOB)
#define MICROPY_HW_UART1_PINS (GPIO_PIN_6 | GPIO_PIN_7)
#define MICROPY_HW_UART2_NAME "XA"
#define MICROPY_HW_UART2_PORT (GPIOA)
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
#define MICROPY_HW_UART6_NAME "YA"
#define MICROPY_HW_UART6_PORT (GPIOC)
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
// I2C busses
#define MICROPY_HW_I2C1_NAME "X"
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C3_NAME "Y"
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_B8)
// SPI busses
#define MICROPY_HW_SPI1_NAME "X"
#define MICROPY_HW_SPI1_NSS (pin_A4) // X5
#define MICROPY_HW_SPI1_SCK (pin_A5) // X6
#define MICROPY_HW_SPI1_MISO (pin_A6) // X7
#define MICROPY_HW_SPI1_MOSI (pin_A7) // X8
#define MICROPY_HW_SPI2_NAME "Y"
#define MICROPY_HW_SPI2_NSS (pin_B12) // Y5
#define MICROPY_HW_SPI2_SCK (pin_B13) // Y6
#define MICROPY_HW_SPI2_MISO (pin_B14) // Y7
#define MICROPY_HW_SPI2_MOSI (pin_B15) // Y8
// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
#define MICROPY_HW_USRSW_PIN (pin_B3)
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// The pyboard has 4 LEDs
#define MICROPY_HW_LED1 (pin_A13) // red
#define MICROPY_HW_LED2 (pin_A14) // green
#define MICROPY_HW_LED3 (pin_A15) // yellow
#define MICROPY_HW_LED4 (pin_B4) // blue
#define MICROPY_HW_LED4_PWM (0) // TIM3 is now a user timer
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_B5)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
// USB config
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USE_ALT_IRQ_FOR_CDC (1)
// MMA accelerometer config
#define MICROPY_HW_MMA_AVDD_PIN (pin_A10)
|
