diff options
Diffstat (limited to 'stmhal/boards/OLIMEX_E407/mpconfigboard.h')
| -rw-r--r-- | stmhal/boards/OLIMEX_E407/mpconfigboard.h | 87 |
1 files changed, 87 insertions, 0 deletions
diff --git a/stmhal/boards/OLIMEX_E407/mpconfigboard.h b/stmhal/boards/OLIMEX_E407/mpconfigboard.h new file mode 100644 index 0000000000..4d1f7ff834 --- /dev/null +++ b/stmhal/boards/OLIMEX_E407/mpconfigboard.h @@ -0,0 +1,87 @@ +#define STM32E407 + +#define MICROPY_HW_BOARD_NAME "OLIMEX STM32-E407" +#define MICROPY_HW_MCU_NAME "STM32F407" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_FLASH (1) +#define MICROPY_HW_HAS_SDCARD (1) +#define MICROPY_HW_HAS_MMA7660 (0) +#define MICROPY_HW_HAS_LIS3DSH (0) +#define MICROPY_HW_HAS_LCD (0) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_TIMER (1) +#define MICROPY_HW_ENABLE_SERVO (0) +#define MICROPY_HW_ENABLE_DAC (1) +#define MICROPY_HW_ENABLE_CAN (1) + +// HSE is 12MHz +#define MICROPY_HW_CLK_PLLM (12) +#define MICROPY_HW_CLK_PLLN (336) +#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) +#define MICROPY_HW_CLK_PLLQ (7) + +// UART config +#if MICROPY_HW_HAS_SWITCH == 0 +#define MICROPY_HW_UART1_PORT (GPIOB) +#define MICROPY_HW_UART1_PINS (GPIO_PIN_6 | GPIO_PIN_7) +#endif + +#define MICROPY_HW_UART2_PORT (GPIOA) +#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3) +#define MICROPY_HW_UART2_RTS (GPIO_PIN_1) +#define MICROPY_HW_UART2_CTS (GPIO_PIN_0) + +#define MICROPY_HW_UART3_PORT (GPIOD) +#define MICROPY_HW_UART3_PINS (GPIO_PIN_8 | GPIO_PIN_9) +#define MICROPY_HW_UART3_RTS (GPIO_PIN_12) +#define MICROPY_HW_UART3_CTS (GPIO_PIN_11) + +#if MICROPY_HW_HAS_SWITCH == 0 +// NOTE: A0 also connects to the user switch. To use UART4 you should +// set MICROPY_HW_HAS_SWITCH to 0, and also remove SB20 (on the back +// of the board near the USER switch). +#define MICROPY_HW_UART4_PORT (GPIOA) +#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1) +#endif + +#define MICROPY_HW_UART6_PORT (GPIOC) +#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7) + +// I2C busses +#define MICROPY_HW_I2C1_SCL (pin_B6) +#define MICROPY_HW_I2C1_SDA (pin_B7) +#define MICROPY_HW_I2C2_SCL (pin_B10) +#define MICROPY_HW_I2C2_SDA (pin_B11) + +// SPI busses +#define MICROPY_HW_SPI1_NSS (pin_A4) +#define MICROPY_HW_SPI1_SCK (pin_A5) +#define MICROPY_HW_SPI1_MISO (pin_A6) +#define MICROPY_HW_SPI1_MOSI (pin_A7) +#define MICROPY_HW_SPI2_NSS (pin_B12) +#define MICROPY_HW_SPI2_SCK (pin_B13) +#define MICROPY_HW_SPI2_MISO (pin_B14) +#define MICROPY_HW_SPI2_MOSI (pin_B15) + +// USRSW is pulled low. Pressing the button makes the input go high. +#define MICROPY_HW_USRSW_PIN (pin_A0) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) + +// LEDs +#define MICROPY_HW_LED1 (pin_C13) +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRH = pin->pin_mask) +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRL = pin->pin_mask) + +// SD card detect switch +#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C11) +#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) +#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) + +// USB config +#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9) +#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) |