diff options
| -rw-r--r-- | ports/stm32/boards/STM32H573I_DK/bdev.c | 45 | ||||
| -rw-r--r-- | ports/stm32/boards/STM32H573I_DK/mpconfigboard.h | 113 | ||||
| -rw-r--r-- | ports/stm32/boards/STM32H573I_DK/mpconfigboard.mk | 15 | ||||
| -rw-r--r-- | ports/stm32/boards/STM32H573I_DK/pins.csv | 149 | ||||
| -rw-r--r-- | ports/stm32/boards/STM32H573I_DK/stm32h5xx_hal_conf.h | 19 |
5 files changed, 341 insertions, 0 deletions
diff --git a/ports/stm32/boards/STM32H573I_DK/bdev.c b/ports/stm32/boards/STM32H573I_DK/bdev.c new file mode 100644 index 0000000000..b304734237 --- /dev/null +++ b/ports/stm32/boards/STM32H573I_DK/bdev.c @@ -0,0 +1,45 @@ +/* + * This file is part of the MicroPython project, http://micropython.org/ + * + * The MIT License (MIT) + * + * Copyright (c) 2023 Damien P. George + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "storage.h" +#include "octospi.h" + +#if MICROPY_HW_SPIFLASH_ENABLE_CACHE +static mp_spiflash_cache_t spi_bdev_cache; +#endif + +// External SPI flash uses hardware OCTOSPI interface (in 1-line mode). + +const mp_spiflash_config_t spiflash_config = { + .bus_kind = MP_SPIFLASH_BUS_QSPI, // spiflash driver doesn't yet support OSPI + .bus.u_qspi.data = NULL, + .bus.u_qspi.proto = &octospi_proto, + #if MICROPY_HW_SPIFLASH_ENABLE_CACHE + .cache = &spi_bdev_cache, + #endif +}; + +spi_bdev_t spi_bdev; diff --git a/ports/stm32/boards/STM32H573I_DK/mpconfigboard.h b/ports/stm32/boards/STM32H573I_DK/mpconfigboard.h new file mode 100644 index 0000000000..01064325da --- /dev/null +++ b/ports/stm32/boards/STM32H573I_DK/mpconfigboard.h @@ -0,0 +1,113 @@ +#define MICROPY_HW_BOARD_NAME "STM32H573I-DK" +#define MICROPY_HW_MCU_NAME "STM32H573IIK3Q" + +#define MICROPY_PY_PYB_LEGACY (0) +#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_ADC (1) +#define MICROPY_HW_ENABLE_DAC (0) // requires DMA +#define MICROPY_HW_ENABLE_USB (1) +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_FLASH (1) + +#if 1 +// The board has a 25MHz oscillator, the following gives 250MHz CPU speed +#define MICROPY_HW_CLK_USE_BYPASS (1) +#define MICROPY_HW_CLK_PLLM (5) +#define MICROPY_HW_CLK_PLLN (100) +#define MICROPY_HW_CLK_PLLP (2) +#define MICROPY_HW_CLK_PLLQ (2) +#define MICROPY_HW_CLK_PLLR (2) +#define MICROPY_HW_CLK_PLLVCI_LL (LL_RCC_PLLINPUTRANGE_4_8) +#define MICROPY_HW_CLK_PLLVCO_LL (LL_RCC_PLLVCORANGE_WIDE) +#define MICROPY_HW_CLK_PLLFRAC (0) +#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_5 +#else +// Use 64MHz HSI to clock the CPU at 200MHz +#define MICROPY_HW_CLK_USE_HSI (1) // 64MHz +#define MICROPY_HW_CLK_PLLM (16) +#define MICROPY_HW_CLK_PLLN (100) +#define MICROPY_HW_CLK_PLLP (2) +#define MICROPY_HW_CLK_PLLQ (2) +#define MICROPY_HW_CLK_PLLR (2) +#define MICROPY_HW_CLK_PLLVCI_LL (LL_RCC_PLLINPUTRANGE_4_8) +#define MICROPY_HW_CLK_PLLVCO_LL (LL_RCC_PLLVCORANGE_WIDE) +#define MICROPY_HW_CLK_PLLFRAC (0) +#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4 // VOS0, 168-210MHz +#endif + +// PLL3 with Q output at 48MHz for USB +#define MICROPY_HW_CLK_PLL3M (25) +#define MICROPY_HW_CLK_PLL3N (192) +#define MICROPY_HW_CLK_PLL3P (2) +#define MICROPY_HW_CLK_PLL3Q (4) +#define MICROPY_HW_CLK_PLL3R (2) +#define MICROPY_HW_CLK_PLL3FRAC (0) +#define MICROPY_HW_CLK_PLL3VCI_LL (LL_RCC_PLLINPUTRANGE_1_2) +#define MICROPY_HW_CLK_PLL3VCO_LL (LL_RCC_PLLVCORANGE_MEDIUM) + +// There is an external 32kHz oscillator +#define MICROPY_HW_RTC_USE_LSE (1) + +// 512MBit +#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE +#define MICROPY_HW_OSPIFLASH_SIZE_BITS_LOG2 (29) +#define MICROPY_HW_OSPIFLASH_CS (pin_G6) +#define MICROPY_HW_OSPIFLASH_SCK (pin_F10) +#define MICROPY_HW_OSPIFLASH_IO0 (pin_B1) +#define MICROPY_HW_OSPIFLASH_IO1 (pin_D12) +#define MICROPY_HW_OSPIFLASH_IO2 (pin_C2) +#define MICROPY_HW_OSPIFLASH_IO3 (pin_D13) +#define MICROPY_HW_OSPIFLASH_IO4 (pin_H2) +#define MICROPY_HW_OSPIFLASH_IO5 (pin_H3) +#define MICROPY_HW_OSPIFLASH_IO6 (pin_G9) +#define MICROPY_HW_OSPIFLASH_IO7 (pin_C0) +#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1) +#define MICROPY_HW_BDEV_SPIFLASH (&spi_bdev) +#define MICROPY_HW_BDEV_SPIFLASH_CONFIG (&spiflash_config) +#define MICROPY_HW_BDEV_SPIFLASH_SIZE_BYTES ((1 << MICROPY_HW_OSPIFLASH_SIZE_BITS_LOG2) / 8) +#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol +#endif + +// UART buses +#define MICROPY_HW_UART1_TX (pin_A9) +#define MICROPY_HW_UART1_RX (pin_A10) +#define MICROPY_HW_UART3_TX (pin_B10) // Arduino Connector CN15-Pin2 (D1) +#define MICROPY_HW_UART3_RX (pin_B11) // Arduino Connector CN15-Pin1 (D0) +#define MICROPY_HW_UART_REPL PYB_UART_1 +#define MICROPY_HW_UART_REPL_BAUD 115200 + +// I2C buses +#define MICROPY_HW_I2C1_SCL (pin_B6) // Arduino Connector CN13-Pin10 (D15) +#define MICROPY_HW_I2C1_SDA (pin_B7) // Arduino Connector CN13-Pin9 (D14) + +// SPI buses +#define MICROPY_HW_SPI2_NSS (pin_A3) // Arduino Connector CN13-Pin3 (D10) +#define MICROPY_HW_SPI2_SCK (pin_I1) // Arduino Connector CN13-Pin6 (D13) +#define MICROPY_HW_SPI2_MISO (pin_I2) // Arduino Connector CN13-Pin5 (D12) +#define MICROPY_HW_SPI2_MOSI (pin_B15) // Arduino Connector CN13-Pin4 (D11) + +// USRSW is pulled low. Pressing the button makes the input go high. +#define MICROPY_HW_USRSW_PIN (pin_C13) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) + +// LEDs +#define MICROPY_HW_LED1 (pin_I9) // green +#define MICROPY_HW_LED2 (pin_I8) // orange +#define MICROPY_HW_LED3 (pin_F1) // red +#define MICROPY_HW_LED4 (pin_F4) // blue +#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin)) +#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin)) + +// USB config +#define MICROPY_HW_USB_FS (1) +#define MICROPY_HW_USB_MAIN_DEV (USB_PHY_FS_ID) + +/******************************************************************************/ +// Variable and function declarations + +extern const struct _mp_spiflash_config_t spiflash_config; +extern struct _spi_bdev_t spi_bdev; diff --git a/ports/stm32/boards/STM32H573I_DK/mpconfigboard.mk b/ports/stm32/boards/STM32H573I_DK/mpconfigboard.mk new file mode 100644 index 0000000000..99d3923f20 --- /dev/null +++ b/ports/stm32/boards/STM32H573I_DK/mpconfigboard.mk @@ -0,0 +1,15 @@ +USE_MBOOT ?= 0 + +# MCU settings +MCU_SERIES = h5 +CMSIS_MCU = STM32H573xx +MICROPY_FLOAT_IMPL = single +AF_FILE = boards/stm32h573_af.csv + +ifeq ($(USE_MBOOT),1) +LD_FILES = boards/stm32h573xi.ld boards/common_bl.ld +TEXT0_ADDR = 0x08008000 +else +LD_FILES = boards/stm32h573xi.ld boards/common_basic.ld +TEXT0_ADDR = 0x08000000 +endif diff --git a/ports/stm32/boards/STM32H573I_DK/pins.csv b/ports/stm32/boards/STM32H573I_DK/pins.csv new file mode 100644 index 0000000000..5672bc4922 --- /dev/null +++ b/ports/stm32/boards/STM32H573I_DK/pins.csv @@ -0,0 +1,149 @@ +,PA0 +,PA1 +,PA2 +,PA3 +,PA4 +,PA5 +,PA6 +,PA7 +,PA8 +,PA9 +,PA10 +,PA11 +,PA12 +,PA13 +,PA14 +,PA15 +,PB0 +,PB1 +,PB2 +,PB3 +,PB4 +,PB5 +,PB6 +,PB7 +,PB8 +,PB9 +,PB10 +,PB11 +,PB12 +,PB13 +,PB14 +,PB15 +,PC0 +,PC1 +,PC2 +,PC3 +,PC4 +,PC5 +,PC6 +,PC7 +,PC8 +,PC9 +,PC10 +,PC11 +,PC12 +,PC13 +,PC14 +,PC15 +,PD0 +,PD1 +,PD2 +,PD3 +,PD4 +,PD5 +,PD6 +,PD7 +,PD8 +,PD9 +,PD10 +,PD11 +,PD12 +,PD13 +,PD14 +,PD15 +,PE0 +,PE1 +,PE2 +,PE3 +,PE4 +,PE5 +,PE6 +,PE7 +,PE8 +,PE9 +,PE10 +,PE11 +,PE12 +,PE13 +,PE14 +,PE15 +,PF0 +,PF1 +,PF2 +,PF3 +,PF4 +,PF5 +,PF6 +,PF7 +,PF8 +,PF9 +,PF10 +,PF11 +,PF12 +,PF13 +,PF14 +,PF15 +,PG0 +,PG1 +,PG2 +,PG3 +,PG4 +,PG5 +,PG6 +,PG7 +,PG8 +,PG9 +,PG10 +,PG11 +,PG12 +,PG13 +,PG14 +,PG15 +,PH0 +,PH1 +,PH2 +,PH3 +,PH4 +,PH5 +,PH6 +,PH7 +,PH8 +,PH9 +,PH10 +,PH11 +,PH12 +,PH13 +,PH14 +,PH15 +,PI0 +,PI1 +,PI2 +,PI3 +,PI4 +,PI5 +,PI6 +,PI7 +,PI8 +,PI9 +,PI10 +,PI11 +,PI12 +,PI13 +,PI14 +,PI15 +LED1,G11 +LED2,G2 +SW,PC13 +UART3_TX,PB10 +UART3_RX,PB11 diff --git a/ports/stm32/boards/STM32H573I_DK/stm32h5xx_hal_conf.h b/ports/stm32/boards/STM32H573I_DK/stm32h5xx_hal_conf.h new file mode 100644 index 0000000000..6b32ffb185 --- /dev/null +++ b/ports/stm32/boards/STM32H573I_DK/stm32h5xx_hal_conf.h @@ -0,0 +1,19 @@ +/* This file is part of the MicroPython project, http://micropython.org/ + * The MIT License (MIT) + * Copyright (c) 2023 Damien P. George + */ +#ifndef MICROPY_INCLUDED_STM32H5XX_HAL_CONF_H +#define MICROPY_INCLUDED_STM32H5XX_HAL_CONF_H + +// Oscillator values in Hz +#define HSE_VALUE (25000000) +#define LSE_VALUE (32768) +#define EXTERNAL_CLOCK_VALUE (12288000) + +#include "boards/stm32h5xx_hal_conf_base.h" + +// Oscillator timeouts in ms +#define HSE_STARTUP_TIMEOUT (100) +#define LSE_STARTUP_TIMEOUT (5000) + +#endif // MICROPY_INCLUDED_STM32H5XX_HAL_CONF_H |