summaryrefslogtreecommitdiffstatshomepage
diff options
context:
space:
mode:
Diffstat
-rw-r--r--stmhal/lcd.c666
-rw-r--r--stmhal/lcd.h4
-rw-r--r--stmhal/main.c10
-rw-r--r--stmhal/modpyb.c5
-rw-r--r--stmhal/printf.c14
-rw-r--r--stmhal/pybstdio.c7
-rw-r--r--stmhal/qstrdefsport.h12
-rw-r--r--stmhal/usb.c1
8 files changed, 384 insertions, 335 deletions
diff --git a/stmhal/lcd.c b/stmhal/lcd.c
index 9d42ab4a4c..6d55448409 100644
--- a/stmhal/lcd.c
+++ b/stmhal/lcd.c
@@ -39,376 +39,430 @@
#include "obj.h"
#include "runtime.h"
-#include "systick.h"
+#include "pin.h"
+#include "genhdr/pins.h"
+#include "bufhelper.h"
+#include "spi.h"
#include "font_petme128_8x8.h"
#include "lcd.h"
-#if defined(PYBV3)
-#define PYB_LCD_PORT (GPIOA)
-#define PYB_LCD_CS1_PIN (GPIO_PIN_0)
-#define PYB_LCD_RST_PIN (GPIO_PIN_1)
-#define PYB_LCD_A0_PIN (GPIO_PIN_2)
-#define PYB_LCD_SCL_PIN (GPIO_PIN_3)
-#define PYB_LCD_SI_PIN (GPIO_PIN_4)
-#elif defined(PYBV4) || defined(PYBV10)
-// X position
-#define PYB_LCD_PORT (GPIOA)
-#define PYB_LCD_CS1_PIN (GPIO_PIN_2) // X3
-#define PYB_LCD_RST_PIN (GPIO_PIN_3) // X4
-#define PYB_LCD_A0_PIN (GPIO_PIN_4) // X5
-#define PYB_LCD_SCL_PIN (GPIO_PIN_5) // X6
-#define PYB_LCD_SI_PIN (GPIO_PIN_7) // X8
-#define PYB_LCD_BL_PORT (GPIOC)
-#define PYB_LCD_BL_PIN (GPIO_PIN_5) // X12
-/*
-// Y position
-#define PYB_LCD_PORT (GPIOB)
-#define PYB_LCD_CS1_PIN (GPIO_PIN_8) // Y3 = PB8
-#define PYB_LCD_RST_PIN (GPIO_PIN_9) // Y4 = PB9
-#define PYB_LCD_A0_PIN (GPIO_PIN_12) // Y5 = PB12
-#define PYB_LCD_SCL_PIN (GPIO_PIN_13) // Y6 = PB13
-#define PYB_LCD_SI_PIN (GPIO_PIN_15) // Y8 = PB15
-#define PYB_LCD_BL_PORT (GPIOB)
-#define PYB_LCD_BL_PIN (GPIO_PIN_1) // Y12 = PB1
-*/
-#elif defined(STM32F4DISC)
-/* Configure if needed */
-#define PYB_LCD_PORT (GPIOA)
-#define PYB_LCD_CS1_PIN (GPIO_PIN_2) // X3
-#define PYB_LCD_RST_PIN (GPIO_PIN_3) // X4
-#define PYB_LCD_A0_PIN (GPIO_PIN_4) // X5
-#define PYB_LCD_SCL_PIN (GPIO_PIN_5) // X6
-#define PYB_LCD_SI_PIN (GPIO_PIN_7) // X8
-#define PYB_LCD_BL_PORT (GPIOC)
-#define PYB_LCD_BL_PIN (GPIO_PIN_5) // X12
-#endif
-
#define LCD_INSTR (0)
#define LCD_DATA (1)
-static void lcd_delay(void) {
+#define LCD_CHAR_BUF_W (16)
+#define LCD_CHAR_BUF_H (4)
+
+#define LCD_PIX_BUF_W (128)
+#define LCD_PIX_BUF_H (32)
+#define LCD_PIX_BUF_BYTE_SIZE (LCD_PIX_BUF_W * LCD_PIX_BUF_H / 8)
+
+typedef struct _pyb_lcd_obj_t {
+ mp_obj_base_t base;
+
+ // hardware control for the LCD
+ SPI_HandleTypeDef *spi;
+ const pin_obj_t *pin_cs1;
+ const pin_obj_t *pin_rst;
+ const pin_obj_t *pin_a0;
+ const pin_obj_t *pin_bl;
+
+ // character buffer for stdout-like output
+ char char_buffer[LCD_CHAR_BUF_W * LCD_CHAR_BUF_H];
+ int line;
+ int column;
+ int next_line;
+
+ // double buffering for pixel buffer
+ byte pix_buf[LCD_PIX_BUF_BYTE_SIZE];
+ byte pix_buf2[LCD_PIX_BUF_BYTE_SIZE];
+} pyb_lcd_obj_t;
+
+STATIC void lcd_delay(void) {
__asm volatile ("nop\nnop");
}
-static void lcd_out(int instr_data, uint8_t i) {
+STATIC void lcd_out(pyb_lcd_obj_t *lcd, int instr_data, uint8_t i) {
lcd_delay();
- PYB_LCD_PORT->BSRRH = PYB_LCD_CS1_PIN; // CS=0; enable
+ lcd->pin_cs1->gpio->BSRRH = lcd->pin_cs1->pin_mask; // CS=0; enable
if (instr_data == LCD_INSTR) {
- PYB_LCD_PORT->BSRRH = PYB_LCD_A0_PIN; // A0=0; select instr reg
+ lcd->pin_a0->gpio->BSRRH = lcd->pin_a0->pin_mask; // A0=0; select instr reg
} else {
- PYB_LCD_PORT->BSRRL = PYB_LCD_A0_PIN; // A0=1; select data reg
- }
- // send byte bigendian, latches on rising clock
- for (uint32_t n = 0; n < 8; n++) {
- lcd_delay();
- PYB_LCD_PORT->BSRRH = PYB_LCD_SCL_PIN; // SCL=0
- if ((i & 0x80) == 0) {
- PYB_LCD_PORT->BSRRH = PYB_LCD_SI_PIN; // SI=0
- } else {
- PYB_LCD_PORT->BSRRL = PYB_LCD_SI_PIN; // SI=1
- }
- i <<= 1;
- lcd_delay();
- PYB_LCD_PORT->BSRRL = PYB_LCD_SCL_PIN; // SCL=1
+ lcd->pin_a0->gpio->BSRRL = lcd->pin_a0->pin_mask; // A0=1; select data reg
}
- PYB_LCD_PORT->BSRRL = PYB_LCD_CS1_PIN; // CS=1; disable
-
- /*
- in Python, native types:
- CS1_PIN(const) = 0
- n = int(0)
- delay_ms(0)
- PORT[word:BSRRH] = 1 << CS1_PIN
- for n in range(0, 8):
- delay_ms(0)
- PORT[word:BSRRH] = 1 << SCL_PIN
- if i & 0x80 == 0:
- PORT[word:BSRRH] = 1 << SI_PIN
- else:
- PORT[word:BSRRL] = 1 << SI_PIN
- i <<= 1
- delay_ms(0)
- PORT[word:BSRRL] = 1 << SCL_PIN
- */
+ lcd_delay();
+ HAL_SPI_Transmit(lcd->spi, &i, 1, 1000);
}
-/*
-static void lcd_data_out(uint8_t i) {
- delay_ms(0);
- PYB_LCD_PORT->BSRRH = PYB_LCD_CS1_PIN; // CS=0; enable
- PYB_LCD_PORT->BSRRL = PYB_LCD_A0_PIN; // A0=1; select data reg
- // send byte bigendian, latches on rising clock
- for (uint32_t n = 0; n < 8; n++) {
- delay_ms(0);
- PYB_LCD_PORT->BSRRH = PYB_LCD_SCL_PIN; // SCL=0
- if ((i & 0x80) == 0) {
- PYB_LCD_PORT->BSRRH = PYB_LCD_SI_PIN; // SI=0
+// write a string to the LCD at the current cursor location
+// output it straight away (doesn't use the pixel buffer)
+STATIC void lcd_write_strn(pyb_lcd_obj_t *lcd, const char *str, unsigned int len) {
+ int redraw_min = lcd->line * LCD_CHAR_BUF_W + lcd->column;
+ int redraw_max = redraw_min;
+ for (; len > 0; len--, str++) {
+ // move to next line if needed
+ if (lcd->next_line) {
+ if (lcd->line + 1 < LCD_CHAR_BUF_H) {
+ lcd->line += 1;
+ } else {
+ lcd->line = LCD_CHAR_BUF_H - 1;
+ for (int i = 0; i < LCD_CHAR_BUF_W * (LCD_CHAR_BUF_H - 1); i++) {
+ lcd->char_buffer[i] = lcd->char_buffer[i + LCD_CHAR_BUF_W];
+ }
+ for (int i = 0; i < LCD_CHAR_BUF_W; i++) {
+ lcd->char_buffer[LCD_CHAR_BUF_W * (LCD_CHAR_BUF_H - 1) + i] = ' ';
+ }
+ redraw_min = 0;
+ redraw_max = LCD_CHAR_BUF_W * LCD_CHAR_BUF_H;
+ }
+ lcd->next_line = 0;
+ lcd->column = 0;
+ }
+ if (*str == '\n') {
+ lcd->next_line = 1;
+ } else if (*str == '\r') {
+ lcd->column = 0;
+ } else if (*str == '\b') {
+ if (lcd->column > 0) {
+ lcd->column--;
+ redraw_min = 0; // could optimise this to not redraw everything
+ }
+ } else if (lcd->column >= LCD_CHAR_BUF_W) {
+ lcd->next_line = 1;
+ str -= 1;
+ len += 1;
} else {
- PYB_LCD_PORT->BSRRL = PYB_LCD_SI_PIN; // SI=1
+ lcd->char_buffer[lcd->line * LCD_CHAR_BUF_W + lcd->column] = *str;
+ lcd->column += 1;
+ int max = lcd->line * LCD_CHAR_BUF_W + lcd->column;
+ if (max > redraw_max) {
+ redraw_max = max;
+ }
}
- i <<= 1;
- delay_ms(0);
- PYB_LCD_PORT->BSRRL = PYB_LCD_SCL_PIN; // SCL=1
}
- PYB_LCD_PORT->BSRRL = PYB_LCD_CS1_PIN; // CS=1; disable
-}
-*/
-
-// writes 8 vertical pixels
-// pos 0 is upper left, pos 1 is 8 pixels to right of that, pos 128 is 8 pixels below that
-mp_obj_t lcd_draw_pixel_8(mp_obj_t mp_pos, mp_obj_t mp_val) {
- int pos = mp_obj_get_int(mp_pos);
- int val = mp_obj_get_int(mp_val);
- int page = pos / 128;
- int offset = pos - (page * 128);
- lcd_out(LCD_INSTR, 0xb0 | page); // page address set
- lcd_out(LCD_INSTR, 0x10 | ((offset >> 4) & 0x0f)); // column address set upper
- lcd_out(LCD_INSTR, 0x00 | (offset & 0x0f)); // column address set lower
- lcd_out(LCD_DATA, val); // write data
- return mp_const_none;
-}
-
-#define LCD_BUF_W (16)
-#define LCD_BUF_H (4)
-
-char lcd_char_buffer[LCD_BUF_W * LCD_BUF_H];
-int lcd_line;
-int lcd_column;
-int lcd_next_line;
-#define LCD_PIX_BUF_SIZE (128 * 32 / 8)
-byte lcd_pix_buf[LCD_PIX_BUF_SIZE];
-byte lcd_pix_buf2[LCD_PIX_BUF_SIZE];
-
-mp_obj_t lcd_pix_clear(void) {
- memset(lcd_pix_buf, 0, LCD_PIX_BUF_SIZE);
- memset(lcd_pix_buf2, 0, LCD_PIX_BUF_SIZE);
- return mp_const_none;
-}
-
-mp_obj_t lcd_pix_get(mp_obj_t mp_x, mp_obj_t mp_y) {
- int x = mp_obj_get_int(mp_x);
- int y = mp_obj_get_int(mp_y);
- if (0 <= x && x <= 127 && 0 <= y && y <= 31) {
- uint byte_pos = x + 128 * ((uint)y >> 3);
- if (lcd_pix_buf[byte_pos] & (1 << (y & 7))) {
- return mp_obj_new_int(1);
+ // we must draw upside down, because the LCD is upside down
+ for (int i = redraw_min; i < redraw_max; i++) {
+ uint page = i / LCD_CHAR_BUF_W;
+ uint offset = 8 * (LCD_CHAR_BUF_W - 1 - (i - (page * LCD_CHAR_BUF_W)));
+ lcd_out(lcd, LCD_INSTR, 0xb0 | page); // page address set
+ lcd_out(lcd, LCD_INSTR, 0x10 | ((offset >> 4) & 0x0f)); // column address set upper
+ lcd_out(lcd, LCD_INSTR, 0x00 | (offset & 0x0f)); // column address set lower
+ int chr = lcd->char_buffer[i];
+ if (chr < 32 || chr > 126) {
+ chr = 127;
}
- }
- return mp_obj_new_int(0);
-}
-
-mp_obj_t lcd_pix_set(mp_obj_t mp_x, mp_obj_t mp_y) {
- int x = mp_obj_get_int(mp_x);
- int y = mp_obj_get_int(mp_y);
- if (0 <= x && x <= 127 && 0 <= y && y <= 31) {
- uint byte_pos = x + 128 * ((uint)y >> 3);
- lcd_pix_buf2[byte_pos] |= 1 << (y & 7);
- }
- return mp_const_none;
-}
-
-mp_obj_t lcd_pix_reset(mp_obj_t mp_x, mp_obj_t mp_y) {
- int x = mp_obj_get_int(mp_x);
- int y = mp_obj_get_int(mp_y);
- if (0 <= x && x <= 127 && 0 <= y && y <= 31) {
- uint byte_pos = x + 128 * ((uint)y >> 3);
- lcd_pix_buf2[byte_pos] &= ~(1 << (y & 7));
- }
- return mp_const_none;
-}
-
-mp_obj_t lcd_pix_show(void) {
- memcpy(lcd_pix_buf, lcd_pix_buf2, LCD_PIX_BUF_SIZE);
- for (uint page = 0; page < 4; page++) {
- lcd_out(LCD_INSTR, 0xb0 | page); // page address set
- lcd_out(LCD_INSTR, 0x10); // column address set upper; 0
- lcd_out(LCD_INSTR, 0x00); // column address set lower; 0
- for (uint i = 0; i < 128; i++) {
- lcd_out(LCD_DATA, lcd_pix_buf[i + 128 * page]);
+ const uint8_t *chr_data = &font_petme128_8x8[(chr - 32) * 8];
+ for (int j = 7; j >= 0; j--) {
+ lcd_out(lcd, LCD_DATA, chr_data[j]);
}
}
- return mp_const_none;
}
-mp_obj_t lcd_print(mp_obj_t text) {
- uint len;
- const char *data = mp_obj_str_get_data(text, &len);
- lcd_print_strn(data, len);
- return mp_const_none;
-}
-
-mp_obj_t lcd_light(mp_obj_t value) {
-#if defined(PYB_LCD_BL_PORT)
- if (mp_obj_is_true(value)) {
- PYB_LCD_BL_PORT->BSRRL = PYB_LCD_BL_PIN; // set pin high to turn backlight on
+STATIC mp_obj_t pyb_lcd_make_new(mp_obj_t type_in, uint n_args, uint n_kw, const mp_obj_t *args) {
+ // check arguments
+ mp_arg_check_num(n_args, n_kw, 1, 1, false);
+
+ // get LCD position
+ const char *lcd_id = mp_obj_str_get_str(args[0]);
+
+ // create lcd object
+ pyb_lcd_obj_t *lcd = m_new_obj(pyb_lcd_obj_t);
+ lcd->base.type = &pyb_lcd_type;
+
+ // configure pins
+ // TODO accept an SPI object and pin objects for full customisation
+ if ((lcd_id[0] | 0x20) == 'x' && lcd_id[1] == '\0') {
+ lcd->spi = &SPIHandle1;
+ lcd->pin_cs1 = &pin_A2; // X3
+ lcd->pin_rst = &pin_A3; // X4
+ lcd->pin_a0 = &pin_A4; // X5
+ lcd->pin_bl = &pin_C5; // X12
+ } else if ((lcd_id[0] | 0x20) == 'y' && lcd_id[1] == '\0') {
+ lcd->spi = &SPIHandle2;
+ lcd->pin_cs1 = &pin_B8; // Y3
+ lcd->pin_rst = &pin_B9; // Y4
+ lcd->pin_a0 = &pin_B12; // Y5
+ lcd->pin_bl = &pin_B1; // Y12
} else {
- PYB_LCD_BL_PORT->BSRRH = PYB_LCD_BL_PIN; // set pin low to turn backlight off
+ nlr_raise(mp_obj_new_exception_msg_varg(&mp_type_ValueError, "LCD bus '%s' does not exist", lcd_id));
}
-#endif
- return mp_const_none;
-}
-static mp_obj_t mp_lcd = MP_OBJ_NULL;
+ // init the SPI bus
+ SPI_InitTypeDef *init = &lcd->spi->Init;
+ init->Mode = SPI_MODE_MASTER;
-static mp_obj_t pyb_lcd_init(void) {
- if (mp_lcd != MP_OBJ_NULL) {
- // already init'd
- return mp_lcd;
+ // compute the baudrate prescaler from the desired baudrate
+ // select a prescaler that yields at most the desired baudrate
+ uint spi_clock;
+ if (lcd->spi->Instance == SPI1) {
+ // SPI1 is on APB2
+ spi_clock = HAL_RCC_GetPCLK2Freq();
+ } else {
+ // SPI2 and SPI3 are on APB1
+ spi_clock = HAL_RCC_GetPCLK1Freq();
}
-
- // set the outputs high
- PYB_LCD_PORT->BSRRL = PYB_LCD_CS1_PIN;
- PYB_LCD_PORT->BSRRL = PYB_LCD_RST_PIN;
- PYB_LCD_PORT->BSRRL = PYB_LCD_A0_PIN;
- PYB_LCD_PORT->BSRRL = PYB_LCD_SCL_PIN;
- PYB_LCD_PORT->BSRRL = PYB_LCD_SI_PIN;
-
- // make them push/pull outputs
+ uint br_prescale = spi_clock / 16000000; // datasheet says LCD can run at 20MHz, but we go for 16MHz
+ if (br_prescale <= 2) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; }
+ else if (br_prescale <= 4) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_4; }
+ else if (br_prescale <= 8) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_8; }
+ else if (br_prescale <= 16) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_16; }
+ else if (br_prescale <= 32) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32; }
+ else if (br_prescale <= 64) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_64; }
+ else if (br_prescale <= 128) { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_128; }
+ else { init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_256; }
+
+ // data is sent bigendian, latches on rising clock
+ init->CLKPolarity = SPI_POLARITY_HIGH;
+ init->CLKPhase = SPI_PHASE_2EDGE;
+ init->Direction = SPI_DIRECTION_2LINES;
+ init->DataSize = SPI_DATASIZE_8BIT;
+ init->NSS = SPI_NSS_SOFT;
+ init->FirstBit = SPI_FIRSTBIT_MSB;
+ init->TIMode = SPI_TIMODE_DISABLED;
+ init->CRCCalculation = SPI_CRCCALCULATION_DISABLED;
+ init->CRCPolynomial = 0;
+
+ // init the SPI bus
+ spi_init(lcd->spi);
+
+ // set the pins to default values
+ lcd->pin_cs1->gpio->BSRRL = lcd->pin_cs1->pin_mask;
+ lcd->pin_rst->gpio->BSRRL = lcd->pin_rst->pin_mask;
+ lcd->pin_a0->gpio->BSRRL = lcd->pin_a0->pin_mask;
+ lcd->pin_bl->gpio->BSRRH = lcd->pin_bl->pin_mask;
+
+ // init the pins to be push/pull outputs
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
GPIO_InitStructure.Pull = GPIO_NOPULL;
- GPIO_InitStructure.Pin = PYB_LCD_CS1_PIN | PYB_LCD_RST_PIN | PYB_LCD_A0_PIN | PYB_LCD_SCL_PIN | PYB_LCD_SI_PIN;
- HAL_GPIO_Init(PYB_LCD_PORT, &GPIO_InitStructure);
-#if defined(PYB_LCD_BL_PORT)
- // backlight drive pin, starts low (off)
- PYB_LCD_BL_PORT->BSRRH = PYB_LCD_BL_PIN;
- GPIO_InitStructure.Pin = PYB_LCD_BL_PIN;
- GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP;
- GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
- GPIO_InitStructure.Pull = GPIO_NOPULL;
- HAL_GPIO_Init(PYB_LCD_BL_PORT, &GPIO_InitStructure);
-#endif
+ GPIO_InitStructure.Pin = lcd->pin_cs1->pin_mask;
+ HAL_GPIO_Init(lcd->pin_cs1->gpio, &GPIO_InitStructure);
+
+ GPIO_InitStructure.Pin = lcd->pin_rst->pin_mask;
+ HAL_GPIO_Init(lcd->pin_rst->gpio, &GPIO_InitStructure);
+
+ GPIO_InitStructure.Pin = lcd->pin_a0->pin_mask;
+ HAL_GPIO_Init(lcd->pin_a0->gpio, &GPIO_InitStructure);
+
+ GPIO_InitStructure.Pin = lcd->pin_bl->pin_mask;
+ HAL_GPIO_Init(lcd->pin_bl->gpio, &GPIO_InitStructure);
// init the LCD
HAL_Delay(1); // wait a bit
- PYB_LCD_PORT->BSRRH = PYB_LCD_RST_PIN; // RST=0; reset
+ lcd->pin_rst->gpio->BSRRH = lcd->pin_rst->pin_mask; // RST=0; reset
HAL_Delay(1); // wait for reset; 2us min
- PYB_LCD_PORT->BSRRL = PYB_LCD_RST_PIN; // RST=1; enable
+ lcd->pin_rst->gpio->BSRRL = lcd->pin_rst->pin_mask; // RST=1; enable
HAL_Delay(1); // wait for reset; 2us min
- lcd_out(LCD_INSTR, 0xa0); // ADC select, normal
- lcd_out(LCD_INSTR, 0xc8); // common output mode select, reverse
- lcd_out(LCD_INSTR, 0xa2); // LCD bias set, 1/9 bias
- lcd_out(LCD_INSTR, 0x2f); // power control set, 0b111=(booster on, vreg on, vfollow on)
- lcd_out(LCD_INSTR, 0x21); // v0 voltage regulator internal resistor ratio set, 0b001=small
- lcd_out(LCD_INSTR, 0x81); // electronic volume mode set
- lcd_out(LCD_INSTR, 0x34); // electronic volume register set, 0b110100
- lcd_out(LCD_INSTR, 0x40); // display start line set, 0
- lcd_out(LCD_INSTR, 0xaf); // LCD display, on
-
- // clear display
+ lcd_out(lcd, LCD_INSTR, 0xa0); // ADC select, normal
+ lcd_out(lcd, LCD_INSTR, 0xc0); // common output mode select, normal (this flips the display)
+ lcd_out(lcd, LCD_INSTR, 0xa2); // LCD bias set, 1/9 bias
+ lcd_out(lcd, LCD_INSTR, 0x2f); // power control set, 0b111=(booster on, vreg on, vfollow on)
+ lcd_out(lcd, LCD_INSTR, 0x21); // v0 voltage regulator internal resistor ratio set, 0b001=small
+ lcd_out(lcd, LCD_INSTR, 0x81); // electronic volume mode set
+ lcd_out(lcd, LCD_INSTR, 0x28); // electronic volume register set
+ lcd_out(lcd, LCD_INSTR, 0x40); // display start line set, 0
+ lcd_out(lcd, LCD_INSTR, 0xaf); // LCD display, on
+
+ // clear LCD RAM
for (int page = 0; page < 4; page++) {
- lcd_out(LCD_INSTR, 0xb0 | page); // page address set
- lcd_out(LCD_INSTR, 0x10); // column address set upper
- lcd_out(LCD_INSTR, 0x00); // column address set lower
+ lcd_out(lcd, LCD_INSTR, 0xb0 | page); // page address set
+ lcd_out(lcd, LCD_INSTR, 0x10); // column address set upper
+ lcd_out(lcd, LCD_INSTR, 0x00); // column address set lower
for (int i = 0; i < 128; i++) {
- lcd_out(LCD_DATA, 0x00);
+ lcd_out(lcd, LCD_DATA, 0x00);
}
}
- for (int i = 0; i < LCD_BUF_H * LCD_BUF_W; i++) {
- lcd_char_buffer[i] = ' ';
+ // clear local char buffer
+ memset(lcd->char_buffer, ' ', LCD_CHAR_BUF_H * LCD_CHAR_BUF_W);
+ lcd->line = 0;
+ lcd->column = 0;
+ lcd->next_line = 0;
+
+ // clear local pixel buffer
+ memset(lcd->pix_buf, 0, LCD_PIX_BUF_BYTE_SIZE);
+ memset(lcd->pix_buf2, 0, LCD_PIX_BUF_BYTE_SIZE);
+
+ return lcd;
+}
+
+STATIC mp_obj_t pyb_lcd_command(mp_obj_t self_in, mp_obj_t instr_data_in, mp_obj_t val) {
+ pyb_lcd_obj_t *self = self_in;
+
+ // get whether instr or data
+ int instr_data = mp_obj_get_int(instr_data_in);
+
+ // get the buffer to send from
+ mp_buffer_info_t bufinfo;
+ uint8_t data[1];
+ pyb_buf_get_for_send(val, &bufinfo, data);
+
+ // send the data
+ for (uint i = 0; i < bufinfo.len; i++) {
+ lcd_out(self, instr_data, ((byte*)bufinfo.buf)[i]);
+ }
+
+ return mp_const_none;
+}
+STATIC MP_DEFINE_CONST_FUN_OBJ_3(pyb_lcd_command_obj, pyb_lcd_command);
+
+STATIC mp_obj_t pyb_lcd_contrast(mp_obj_t self_in, mp_obj_t contrast_in) {
+ pyb_lcd_obj_t *self = self_in;
+ int contrast = mp_obj_get_int(contrast_in);
+ if (contrast < 0) {
+ contrast = 0;
+ } else if (contrast > 0x2f) {
+ contrast = 0x2f;
}
- lcd_line = 0;
- lcd_column = 0;
- lcd_next_line = 0;
-
- // Micro Python interface
- mp_obj_t o = mp_obj_new_type(MP_QSTR_LCD, mp_const_empty_tuple, mp_obj_new_dict(0));
- mp_store_attr(o, qstr_from_str("lcd8"), mp_make_function_n(2, lcd_draw_pixel_8));
- mp_store_attr(o, qstr_from_str("clear"), mp_make_function_n(0, lcd_pix_clear));
- mp_store_attr(o, qstr_from_str("get"), mp_make_function_n(2, lcd_pix_get));
- mp_store_attr(o, qstr_from_str("set"), mp_make_function_n(2, lcd_pix_set));
- mp_store_attr(o, qstr_from_str("reset"), mp_make_function_n(2, lcd_pix_reset));
- mp_store_attr(o, qstr_from_str("show"), mp_make_function_n(0, lcd_pix_show));
- mp_store_attr(o, qstr_from_str("text"), mp_make_function_n(1, lcd_print));
- mp_store_attr(o, qstr_from_str("light"), mp_make_function_n(1, lcd_light));
- mp_lcd = o;
- return o;
+ lcd_out(self, LCD_INSTR, 0x81); // electronic volume mode set
+ lcd_out(self, LCD_INSTR, contrast); // electronic volume register set
+ return mp_const_none;
}
+STATIC MP_DEFINE_CONST_FUN_OBJ_2(pyb_lcd_contrast_obj, pyb_lcd_contrast);
-static MP_DEFINE_CONST_FUN_OBJ_0(pyb_lcd_init_obj, pyb_lcd_init);
+STATIC mp_obj_t pyb_lcd_light(mp_obj_t self_in, mp_obj_t value) {
+ pyb_lcd_obj_t *self = self_in;
+ if (mp_obj_is_true(value)) {
+ self->pin_bl->gpio->BSRRL = self->pin_bl->pin_mask; // set pin high to turn backlight on
+ } else {
+ self->pin_bl->gpio->BSRRH = self->pin_bl->pin_mask; // set pin low to turn backlight off
+ }
+ return mp_const_none;
+}
+STATIC MP_DEFINE_CONST_FUN_OBJ_2(pyb_lcd_light_obj, pyb_lcd_light);
-void lcd_init(void) {
- mp_lcd = MP_OBJ_NULL;
- mp_store_name(qstr_from_str("LCD"), (mp_obj_t)&pyb_lcd_init_obj);
+STATIC mp_obj_t pyb_lcd_write(mp_obj_t self_in, mp_obj_t str) {
+ pyb_lcd_obj_t *self = self_in;
+ uint len;
+ const char *data = mp_obj_str_get_data(str, &len);
+ lcd_write_strn(self, data, len);
+ return mp_const_none;
}
+STATIC MP_DEFINE_CONST_FUN_OBJ_2(pyb_lcd_write_obj, pyb_lcd_write);
-void lcd_print_str(const char *str) {
- lcd_print_strn(str, strlen(str));
+STATIC mp_obj_t pyb_lcd_fill(mp_obj_t self_in, mp_obj_t col_in) {
+ pyb_lcd_obj_t *self = self_in;
+ int col = mp_obj_get_int(col_in);
+ if (col) {
+ col = 0xff;
+ }
+ memset(self->pix_buf, col, LCD_PIX_BUF_BYTE_SIZE);
+ memset(self->pix_buf2, col, LCD_PIX_BUF_BYTE_SIZE);
+ return mp_const_none;
}
+STATIC MP_DEFINE_CONST_FUN_OBJ_2(pyb_lcd_fill_obj, pyb_lcd_fill);
-void lcd_print_strn(const char *str, unsigned int len) {
- int redraw_min = lcd_line * LCD_BUF_W + lcd_column;
- int redraw_max = redraw_min;
- int did_new_line = 0;
- for (; len > 0; len--, str++) {
- // move to next line if needed
- if (lcd_next_line) {
- if (lcd_line + 1 < LCD_BUF_H) {
- lcd_line += 1;
- } else {
- lcd_line = LCD_BUF_H - 1;
- for (int i = 0; i < LCD_BUF_W * (LCD_BUF_H - 1); i++) {
- lcd_char_buffer[i] = lcd_char_buffer[i + LCD_BUF_W];
- }
- for (int i = 0; i < LCD_BUF_W; i++) {
- lcd_char_buffer[LCD_BUF_W * (LCD_BUF_H - 1) + i] = ' ';
- }
- redraw_min = 0;
- redraw_max = LCD_BUF_W * LCD_BUF_H;
- }
- lcd_next_line = 0;
- lcd_column = 0;
- did_new_line = 1;
+STATIC mp_obj_t pyb_lcd_get(mp_obj_t self_in, mp_obj_t x_in, mp_obj_t y_in) {
+ pyb_lcd_obj_t *self = self_in;
+ int x = mp_obj_get_int(x_in);
+ int y = mp_obj_get_int(y_in);
+ if (0 <= x && x <= 127 && 0 <= y && y <= 31) {
+ uint byte_pos = x + 128 * ((uint)y >> 3);
+ if (self->pix_buf[byte_pos] & (1 << (y & 7))) {
+ return mp_obj_new_int(1);
}
- if (*str == '\n') {
- lcd_next_line = 1;
- } else if (*str == '\r') {
- lcd_column = 0;
- } else if (*str == '\b') {
- if (lcd_column > 0) {
- lcd_column--;
- }
- } else if (lcd_column >= LCD_BUF_W) {
- lcd_next_line = 1;
- str -= 1;
- len += 1;
+ }
+ return mp_obj_new_int(0);
+}
+STATIC MP_DEFINE_CONST_FUN_OBJ_3(pyb_lcd_get_obj, pyb_lcd_get);
+
+STATIC mp_obj_t pyb_lcd_pixel(uint n_args, const mp_obj_t *args, mp_map_t *kw_args) {
+ pyb_lcd_obj_t *self = args[0];
+ int x = mp_obj_get_int(args[1]);
+ int y = mp_obj_get_int(args[2]);
+ if (0 <= x && x <= 127 && 0 <= y && y <= 31) {
+ uint byte_pos = x + 128 * ((uint)y >> 3);
+ if (mp_obj_get_int(args[3]) == 0) {
+ self->pix_buf2[byte_pos] &= ~(1 << (y & 7));
} else {
- lcd_char_buffer[lcd_line * LCD_BUF_W + lcd_column] = *str;
- lcd_column += 1;
- int max = lcd_line * LCD_BUF_W + lcd_column;
- if (max > redraw_max) {
- redraw_max = max;
- }
+ self->pix_buf2[byte_pos] |= 1 << (y & 7);
}
}
+ return mp_const_none;
+}
+STATIC MP_DEFINE_CONST_FUN_OBJ_VAR_BETWEEN(pyb_lcd_pixel_obj, 4, 4, pyb_lcd_pixel);
- int last_page = -1;
- for (int i = redraw_min; i < redraw_max; i++) {
- int page = i / LCD_BUF_W;
- if (page != last_page) {
- int offset = 8 * (i - (page * LCD_BUF_W));
- lcd_out(LCD_INSTR, 0xb0 | page); // page address set
- lcd_out(LCD_INSTR, 0x10 | ((offset >> 4) & 0x0f)); // column address set upper
- lcd_out(LCD_INSTR, 0x00 | (offset & 0x0f)); // column address set lower
- last_page = page;
- }
- int chr = lcd_char_buffer[i];
- if (chr < 32 || chr > 126) {
+STATIC mp_obj_t pyb_lcd_text(uint n_args, const mp_obj_t *args, mp_map_t *kw_args) {
+ // extract arguments
+ pyb_lcd_obj_t *self = args[0];
+ uint len;
+ const char *data = mp_obj_str_get_data(args[1], &len);
+ int x0 = mp_obj_get_int(args[2]);
+ int y0 = mp_obj_get_int(args[3]);
+ int col = mp_obj_get_int(args[4]);
+
+ // loop over chars
+ for (const char *top = data + len; data < top; data++) {
+ // get char and make sure its in range of font
+ uint chr = *(byte*)data;
+ if (chr < 32 || chr > 127) {
chr = 127;
}
+ // get char data
const uint8_t *chr_data = &font_petme128_8x8[(chr - 32) * 8];
- for (int j = 0; j < 8; j++) {
- lcd_out(LCD_DATA, chr_data[j]);
+ // loop over char data
+ for (uint j = 0; j < 8; j++, x0++) {
+ if (0 <= x0 && x0 < LCD_PIX_BUF_W) { // clip x
+ uint vline_data = chr_data[j]; // each byte of char data is a vertical column of 8 pixels, LSB at top
+ for (int y = y0; vline_data; vline_data >>= 1, y++) { // scan over vertical column
+ if (vline_data & 1) { // only draw if pixel set
+ if (0 <= y && y < LCD_PIX_BUF_H) { // clip y
+ uint byte_pos = x0 + LCD_PIX_BUF_W * ((uint)y >> 3);
+ if (col == 0) {
+ // clear pixel
+ self->pix_buf2[byte_pos] &= ~(1 << (y & 7));
+ } else {
+ // set pixel
+ self->pix_buf2[byte_pos] |= 1 << (y & 7);
+ }
+ }
+ }
+ }
+ }
}
}
- if (did_new_line) {
- HAL_Delay(50);
+ return mp_const_none;
+}
+STATIC MP_DEFINE_CONST_FUN_OBJ_VAR_BETWEEN(pyb_lcd_text_obj, 5, 5, pyb_lcd_text);
+
+STATIC mp_obj_t pyb_lcd_show(mp_obj_t self_in) {
+ pyb_lcd_obj_t *self = self_in;
+ memcpy(self->pix_buf, self->pix_buf2, LCD_PIX_BUF_BYTE_SIZE);
+ for (uint page = 0; page < 4; page++) {
+ lcd_out(self, LCD_INSTR, 0xb0 | page); // page address set
+ lcd_out(self, LCD_INSTR, 0x10); // column address set upper; 0
+ lcd_out(self, LCD_INSTR, 0x00); // column address set lower; 0
+ for (uint i = 0; i < 128; i++) {
+ lcd_out(self, LCD_DATA, self->pix_buf[128 * page + 127 - i]);
+ }
}
+ return mp_const_none;
}
+STATIC MP_DEFINE_CONST_FUN_OBJ_1(pyb_lcd_show_obj, pyb_lcd_show);
+
+STATIC const mp_map_elem_t pyb_lcd_locals_dict_table[] = {
+ // instance methods
+ { MP_OBJ_NEW_QSTR(MP_QSTR_command), (mp_obj_t)&pyb_lcd_command_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_contrast), (mp_obj_t)&pyb_lcd_contrast_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_light), (mp_obj_t)&pyb_lcd_light_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_write), (mp_obj_t)&pyb_lcd_write_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_fill), (mp_obj_t)&pyb_lcd_fill_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_get), (mp_obj_t)&pyb_lcd_get_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_pixel), (mp_obj_t)&pyb_lcd_pixel_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_text), (mp_obj_t)&pyb_lcd_text_obj },
+ { MP_OBJ_NEW_QSTR(MP_QSTR_show), (mp_obj_t)&pyb_lcd_show_obj },
+};
+
+STATIC MP_DEFINE_CONST_DICT(pyb_lcd_locals_dict, pyb_lcd_locals_dict_table);
+
+const mp_obj_type_t pyb_lcd_type = {
+ { &mp_type_type },
+ .name = MP_QSTR_LCD,
+ .make_new = pyb_lcd_make_new,
+ .locals_dict = (mp_obj_t)&pyb_lcd_locals_dict,
+};
#endif // MICROPY_HW_HAS_LCD
diff --git a/stmhal/lcd.h b/stmhal/lcd.h
index 74a3d4d84d..6a4b004bd9 100644
--- a/stmhal/lcd.h
+++ b/stmhal/lcd.h
@@ -24,6 +24,4 @@
* THE SOFTWARE.
*/
-void lcd_init(void);
-void lcd_print_str(const char *str);
-void lcd_print_strn(const char *str, unsigned int len);
+extern const mp_obj_type_t pyb_lcd_type;
diff --git a/stmhal/main.c b/stmhal/main.c
index dbf3ced681..9751dcac2e 100644
--- a/stmhal/main.c
+++ b/stmhal/main.c
@@ -58,7 +58,6 @@
#include "storage.h"
#include "sdcard.h"
#include "ff.h"
-#include "lcd.h"
#include "rng.h"
#include "accel.h"
#include "servo.h"
@@ -95,10 +94,6 @@ void __fatal_error(const char *msg) {
led_state(4, 1);
stdout_tx_strn("\nFATAL ERROR:\n", 14);
stdout_tx_strn(msg, strlen(msg));
-#if 0 && MICROPY_HW_HAS_LCD
- lcd_print_strn("\nFATAL ERROR:\n", 14);
- lcd_print_strn(msg, strlen(msg));
-#endif
for (uint i = 0;;) {
led_toggle(((i++) & 3) + 1);
for (volatile uint delay = 0; delay < 10000000; delay++) {
@@ -333,11 +328,6 @@ soft_reset:
pin_init();
extint_init();
-#if MICROPY_HW_HAS_LCD
- // LCD init (just creates class, init hardware by calling LCD())
- lcd_init();
-#endif
-
// local filesystem init
{
// try to mount the flash
diff --git a/stmhal/modpyb.c b/stmhal/modpyb.c
index 44bcba1d79..fae36b7b69 100644
--- a/stmhal/modpyb.c
+++ b/stmhal/modpyb.c
@@ -54,6 +54,7 @@
#include "accel.h"
#include "servo.h"
#include "dac.h"
+#include "lcd.h"
#include "usb.h"
#include "ff.h"
#include "portmodules.h"
@@ -390,6 +391,10 @@ STATIC const mp_map_elem_t pyb_module_globals_table[] = {
#if MICROPY_HW_HAS_MMA7660
{ MP_OBJ_NEW_QSTR(MP_QSTR_Accel), (mp_obj_t)&pyb_accel_type },
#endif
+
+#if MICROPY_HW_HAS_LCD
+ { MP_OBJ_NEW_QSTR(MP_QSTR_LCD), (mp_obj_t)&pyb_lcd_type },
+#endif
};
STATIC const mp_obj_dict_t pyb_module_globals = {
diff --git a/stmhal/printf.c b/stmhal/printf.c
index 6cfeda2637..e95f23abae 100644
--- a/stmhal/printf.c
+++ b/stmhal/printf.c
@@ -196,23 +196,13 @@ int pfenv_printf(const pfenv_t *pfenv, const char *fmt, va_list args) {
}
void stdout_print_strn(void *data, const char *str, unsigned int len) {
- // send stdout to UART, USB CDC VCP, and LCD if nothing else
- bool any = false;
-
+ // TODO this needs to be replaced with a proper stdio interface ala CPython
+ // send stdout to UART and USB CDC VCP
if (pyb_uart_global_debug != PYB_UART_NONE) {
uart_tx_strn_cooked(pyb_uart_global_debug, str, len);
- any = true;
}
if (usb_vcp_is_enabled()) {
usb_vcp_send_strn_cooked(str, len);
- any = true;
- }
- if (!any) {
-#if 0
-#if MICROPY_HW_HAS_LCD
- lcd_print_strn(str, len);
-#endif
-#endif
}
}
diff --git a/stmhal/pybstdio.c b/stmhal/pybstdio.c
index b7eacf0a0c..59e1ead567 100644
--- a/stmhal/pybstdio.c
+++ b/stmhal/pybstdio.c
@@ -38,11 +38,14 @@
#include "usb.h"
#include "uart.h"
+// TODO make stdin, stdout and stderr writable objects so they can
+// be changed by Python code.
+
void stdout_tx_str(const char *str) {
if (pyb_uart_global_debug != PYB_UART_NONE) {
uart_tx_str(pyb_uart_global_debug, str);
}
-#if defined(USE_HOST_MODE) && MICROPY_HW_HAS_LCD
+#if 0 && defined(USE_HOST_MODE) && MICROPY_HW_HAS_LCD
lcd_print_str(str);
#endif
usb_vcp_send_str(str);
@@ -52,7 +55,7 @@ void stdout_tx_strn(const char *str, uint len) {
if (pyb_uart_global_debug != PYB_UART_NONE) {
uart_tx_strn(pyb_uart_global_debug, str, len);
}
-#if defined(USE_HOST_MODE) && MICROPY_HW_HAS_LCD
+#if 0 && defined(USE_HOST_MODE) && MICROPY_HW_HAS_LCD
lcd_print_strn(str, len);
#endif
usb_vcp_send_strn(str, len);
diff --git a/stmhal/qstrdefsport.h b/stmhal/qstrdefsport.h
index 19a5d7c863..bda3a48687 100644
--- a/stmhal/qstrdefsport.h
+++ b/stmhal/qstrdefsport.h
@@ -57,7 +57,6 @@ Q(have_cdc)
Q(hid)
Q(time)
Q(rng)
-Q(LCD)
Q(SD)
Q(SDcard)
Q(FileIO)
@@ -247,6 +246,17 @@ Q(sleep)
// for input
Q(input)
+// for LCD class
+Q(LCD)
+Q(command)
+Q(contrast)
+Q(light)
+Q(fill)
+Q(get)
+Q(pixel)
+Q(text)
+Q(show)
+
// for stm module
Q(stm)
Q(mem)
diff --git a/stmhal/usb.c b/stmhal/usb.c
index ef7e8a62eb..50848f4555 100644
--- a/stmhal/usb.c
+++ b/stmhal/usb.c
@@ -199,7 +199,6 @@ void USR_KEYBRD_ProcessData(uint8_t pbuf) {
led_state(4, 1);
USB_OTG_BSP_mDelay(50);
led_state(4, 0);
- //lcd_print_strn((char*)&pbuf, 1);
usb_keyboard_key = pbuf;
}
generated by cgit v1.2.3 (git 2.39.1) at 2025-06-24 20:54:49 +0000